LoRa technology is derived from chirp spread spectrum (CSS) having embedded forward error correction (FEC). A wide band is used for transmissions to counter interference and to handle frequency offsets. The paper investigates low power wide area networks (LPWAN) transmissions in the uplink, where the end nodes are powered by using energy harvested from the surroundings. Long-range (LoRa) networks demonstrate their capability to support Internet of Things (IoT) applications, where the end nodes utilize the harvested energy for transmission to gateways using different spreading factor (SF) codes. The work fairly improves the throughput of the LoRa nodes while keeping the other parameters, like time duration of the energy harvesting (EH), SF, and transmit power, optimally. Initially, a mathematical expression is derived for collisions between packets of the end nodes; keeping this as an important factor, an algorithm is proposed that fairly assigns SFs to the nodes. Simulation results confirm the improvement in packet error rate and time on air when fewer LoRa nodes are used for lower SFs, as compared to higher SFs. The number of LoRa nodes that can communicate using SF = 7 is almost four times as compared to using SF = 11, while maintaining a low packet error rate. Also, for SF = 7, changing the coding rate from 1 to 4 increases time on air by around 20 ms, while time on air increases by 1,200 ms for SF = 12. The energy efficiency is also compared for different SFs and different transmission powers. A lower SF and lower transmission powers are more suitable for smaller distance and provides better energy efficiency.
The Internet of Things concept can be implemented using Long-range wireless access network protocol. The work in this article is done to implement LoRa terrestrial network which will be connected to a satellite in future. The work mainly studies the number of collisions and the impact of it on the network. The work is simulated and is done to determine the number of LoRa nodes which can successfully transmit at a given time. Different combinations of spreading factor and bandwidth at different duty cycles are used to assess the performance of the network.
This research delves into innovative solutions for integrating renewable solar energy into electric vehicle (EV) systems to mitigate limitations associated with battery storage and charging infrastructure. By leveraging advanced technologies, such as phase change materials for efficient thermal management, microgrid‐based charging systems for decentralized energy distribution, and cutting‐edge materials like aerogel composites and polymer solar cells for enhanced energy harvesting, this study addresses critical challenges in sustainable transportation. Through a holistic approach that combines energy efficiency, advanced material science, and renewable energy integration, the research provides actionable insights to enhance EV performance, extend battery life, and reduce greenhouse gas emissions. The findings hold significant implications for improving energy autonomy, enabling sustainable mobility solutions, and fostering environmental conservation in the transportation sector.
In solar cells, efficiency is the most critical parameter. In single‐junction solar cells, efficiency is always limited, so to increase the efficiency beyond a specific range, we need to switch to a tandem configuration. Tandem configuration is the stacking of two different cells together, termed as top and bottom cells, where the electrical properties of these two cells are different. ln this paper, free perovskite material with a wide band gap of 1.5 eV (CsSnGeI 3 ) is used to make the top cell, and a narrow band gap of 1.12 eV crystalline silicon is used to create a bottom cell. The advantage of using perovskite material is its high light conversion rate, which leads to better efficiency. Power conversion efficiency (PEC) for perovskite cells is up to 30%. The proposed cell is simulated by SCAPS‐1D. In this process, the top and bottom cells are calibrated in the standalone conditions before analyzing the tandem configuration, where the optimized thickness for the top cell is 100 nm and that of the bottom cell is 200 nm. To combine both cells, the current of both cells should be matched, where the top cell current acts as a limiting factor. By changing the width of the top cell for a filtered spectrum and integrated filtered power, a matched current of 18.34 mA cm −2 is obtained for the top/bottom cell. The resultant parameters of the proposed tandem solar cell are PCE of approximately 26%, open circuit voltage ( Voc ) of 1.576 V, fill factor (FF) of 90%, and short circuit current ( Jsc ) of 18.34 mA cm −2 . The proposed device can help develop low‐cost applications and high‐efficiency tandem solar cells.
Treating pulmonary diseases is pivotal in healthcare since they are the third leading cause of mortality globally. To aid medical experts in diagnosis, various studies have been conducted using artificial intelligence (AI) compatible devices to analyze lung sounds recorded with a stethoscope. In this paper, four datasets have been considered as a combination of two public datasets to assess the performance of the proposed approach. The signals from each dataset undergo a series of pre-processing steps, encompassing normalization, re-sampling, and framing. Thereafter, eight sub-band filters have been taken into account to segregate distinct frequency bands. The sub-band signals are represented using characteristics such as entropy, \(L^p\) norm, kurtosis, mean absolute deviation, and standard deviation. This characteristic representation for the signals is then fed to the proposed neural network (NN) for training and classification. The NN architecture consists of three fully connected layers and an output layer for classification. Our proposed approach attains 100% accuracy, specificity, and sensitivity, performing consistently well across all four datasets, which highlights the model’s strong generalizability. The proposed architecture is simple, easy to realize, and has a short training time. The classification outcomes obtained through the proposed NN architecture demonstrate its superiority when compared to the existing methods.