Continuous casting is the most common method for producing steel into semi-finished shapes like billets or slabs. Throughout this process, steel experiences mechanical and thermal stresses, which influence its mechanical properties. During continuous casting, decreased formability in steel components leads to crack formation and failure. One reason for this phenomenon is the appearance of the soft ferrite phase during cooling. However, it is unclear under which conditions this ferrite is detrimental to the formability. In the present research, we investigated what microstructural changes decrease the formability of microalloyed steels during continuous casting. We studied the hot compression behaviour of microalloyed steel over temperatures ranging from 650 °C to 1100 °C and strain rates of 0.1 to 0.001 using a Gleeble 3800® (Dynamic Systems Inc, Poestenkill, NY, USA) device. We examined microstructural changes at various deformation conditions using microscopy. Furthermore, we implemented a physically-based model to describe the deformation of austenite and ferrite. The model describes the work hardening and dynamic restoration mechanisms, i.e., discontinuous dynamic recrystallisation in austenite and dynamic recovery in ferrite and austenite. The model considers the stress, strain, and strain rate distribution between phases by describing the dynamic phase transformation during the deformation in iso-work conditions. Increasing the strain rate below the transformation temperature improves hot ductility by reducing dynamic recovery and strain concentration in ferrite. Due to limited grain boundary sliding, the hot ductility improves at lower temperatures (<750 °C). In the single-phase domain, dynamic recrystallisation improves the hot ductility provided that fracture occurs at strains in which dynamic recrystallisation advances. However, at very low strain rates, the ductility decreases due to prolonged time for grain boundary sliding and crack propagation.
22 April 2025 in Materialwissenschaft und Werkstofftechnik
Continuous casting of steel is widely used to manufacture semi‐finished long or flat products. Various stresses are present during slab casting: stresses arise from friction between the mold wall and the solidified shell, thermal stresses on the strand surface, and stresses from bending and straightening operations. Steels present a minimum ductility point during continuous casting in the solid‐state condition. This work aims to answer the metallurgical reasons for the occurrence of the ductility minimum in a micro‐alloyed steel by investigating the microstructural evolution. The samples are in situ melted via induction heating in the BETA250‐5® thermomechanical simulator machine, followed by hot tensile tests conducted at different temperatures and strain rates. The ductility drop is analyzed in the range of 650 °C–1100 °C at different strain rates, 10−2 s−1 to 10−3 s−1. Furthermore, the study investigated the development of the ferrite phase at the prior austenite grain boundaries, the thickness of ferrite, dynamic phase transformation, and the influence of the test conditions on these parameters. The fracture mechanism and ferrite phase thickness are determined from metallography investigations using light optical microscopy and scanning electron microscopy. Finally, the microstructural changes are correlated to the ductility minimum using the measured results.
20 February 2026 in Metallurgical Research & Technology
The ductility behavior of continuously cast steel is a key factor influencing strand quality and crack susceptibility. Therefore, investigating the parameters that affect ductility is of great importance for enhancing the productivity of the method by producing defect-free products. This study investigates the differences in ductility behavior between two microalloyed steels with different C, Mn, Al, Ti, B, and S content subjected to hot tensile testing at strain rates of 10 −2 s −1 and 10 −3 s −1 at 750 °C, 800 °C, and 850 °C. The first material is low-carbon microalloyed steel with a higher amount of Mn, Al, and S, and the second contains higher C, Ti, and B. Both steels were tested after in-situ melting using an induction heating system in a vacuum chamber, followed by a hot tensile test until fracture. An initial microstructural analysis was conducted to study the influence of chemical composition, temperature, and strain rate on both steels. Furthermore, the precipitation kinetics of both steels were evaluated using MatCalc software, which provided predictions for the expected precipitates. The results indicate that the steel with higher C, Ti, and B, and lower Mn and S content exhibits better ductility at both strain rates. This was attributed to the influence of alloying elements on the formation of precipitates and the kinetics of austenite-ferrite transformation, in addition to fewer MnS particles. These effects are associated with the preferential formation of coarse TiN rather than AlN and BN.
Continuous casting is the most common method for producing steel into semi-finished shapes like billets or slabs. Throughout this process, steel experiences mechanical and thermal stresses, which influence its mechanical properties. During continuous casting, decreased formability in steel components leads to crack formation and failure. One reason for this phenomenon is the appearance of the soft ferrite phase during cooling. However, it is unclear under which conditions this ferrite is detrimental to the formability. In the present research, we investigated what microstructural changes decrease the formability of microalloyed steels during continuous casting. We studied the hot compression behaviour of microalloyed steel over temperatures ranging from 650 °C to 1100 °C and strain rates of 0.1 s-1 to 0.001 s-1 using a Gleeble 3800® device. We examined microstructural changes at various deformation conditions using microscopy. Furthermore, we implemented a physically-based model to describe the deformation of austenite and ferrite. The model describes the work hardening and dynamic restoration mechanisms, i.e., discontinuous dynamic recrystallisation (dDRX) in austenite and dynamic recovery (DRV) in ferrite and austenite. The model considers the stress, strain, and strain rate distribution between phases by describing the dynamic phase transformation during the deformation in iso-work conditions. Increasing the strain rate below the transformation temperature improves hot ductility by reducing DRV and strain concentration in ferrite. Due to limited grain boundary sliding, the hot ductility improves at lower temperatures (<750 °C). In the single-phase domain, DRX improves the hot ductility provided that fracture occurs at strains in which DRX advances. However, at very low strain rates, the ductility decreases due to prolonged time for grain boundary sliding and crack propagation.