The in-situ TiB₂/7050Al composite is a new kind of Al-based metal matrix composite (MMC) with super properties, such as low density, improved strength, and wear resistance. This paper, for a deep insight into its cutting performance, involves a study of the chip formation process and finite element simulation during orthogonal cutting in-situ TiB₂/7050Al MMC. With chips, material properties, cutting forces, and tool geometry parameters, the Johnson–Cook (J–C) constitutive equation of in-situ TiB₂/7050Al composite was established. Then, the cutting simulation model was established by applying the Abaqus–Explicit method, and the serrated chip, shear plane, strain rate, and temperature were analyzed. The experimental and simulation results showed that the obtained material’s constitutive equation was of high reliability, and the saw-tooth chips occurred commonly under either low or high cutting speed and small or large feed rate. From result analysis, it was found that the mechanisms of chip formation included plastic deformation, adiabatic shear, shearing slip, and crack extension. In addition, it was found that the existence of small, hard particles reduced the ductility of the MMC and resulted in segmental chips.

Interior residual stresses induced by quenching may cause distortion during subsequent machining processes. Hence, various strategies have been employed to relieve the interior residual stress, such as stretching, post treatment, and other techniques. In this study, the stress distribution inside TiB₂/7050 Al composite extrusions was investigated and the effects of different methods on relieving the quenching-induced stress were compared. Firstly, three TiB₂/7050 Al composite extrusions were treated by stretching, stretching and heat treatment, and stretching and cold treatment processes, respectively. Then, the multiple-cut contour method was employed to assess the residual stresses in the three workpieces. Experimental results indicate that the interior stress of TiB₂/7050 Al composite extrusions after stretching ranges from −89 MPa to +55 MPa, which is larger than that in 7050 aluminum alloy, which ranges from −25 Pa to +25 MPa. The heat treatment performs better than the cold treatment to reduce the post-stretching residual stress, with a reduction of 23.2–46.4% compared to 11.3–40.8%, respectively. From the stress map, it is found that the stress distribution after the heat treatment is more uniform compared with that after the cold treatment.

In situ TiB₂ particle-reinforced 7050Al alloy matrix composites are a new category of particulate metal matrix composites with improved mechanical and physical properties. At present, the study of machining in situ TiB₂/Al composite is limited and no specific study has been presented on cutting force. Based on previous work, experimental investigation of cutting in situ TiB₂/Al composite was carried out in this study to investigate the cutting force, shear angle, mean friction angle, and shear stress. The results indicated that the feed rate, instead of cutting speed, has a significant influence on the shear angle, mean friction angle, shear stress, and forces, which is different from cutting ex situ SiC/Al composites. Meanwhile, based on Merchant’s theory, a force model, which consists of chip formation and ploughing force, was established to have a better understanding of force generation. A comparison of the results show an acceptable agreement between the force model and experiments. Additionally, at varying feed rates, the linear relationship between the shear angle and mean friction angle is still suitable for cutting in situ TiB₂/7050Al alloy composites.

The thermo–mechanical behavior of in situ TiB₂/7050 Al metal matrix composites is investigated by quasi-static and Split Hopkinson Pressure Bar compression tests over a wide range of temperature (20~30 °C) and strain rate (0.001~5000 s⁻¹). Johnson–Cook and Khan–Liu constitutive models determined from curve fitting and constrained optimization are used to predict the flow stress during deformation. In addition, another Johnson–Cook model calculated from an orthogonal cutting experiment and finite element simulation is also compared in this study. The prediction capability of these models is compared in terms of correlation coefficient and average absolute error. Due to the assumptions in orthogonal cutting theory, the determined Johnson–Cook model from cutting cannot describe the material deformation behavior accurately. The results also show that the Khan–Liu model has better performance in characterizing the material’s thermo–mechanical behavior.