This study investigates the hydrogen embrittlement behavior of API X70 linepipe steel. The microstructure was primarily composed of a dislocation-rich bainitic microstructure and polygonal ferrite. Slow strain-rate tests (SSRTs) were performed under both ex situ and in situ electrochemical hydrogen charging conditions to examine the difference between hydrogen diffusion and trapping behaviors. The ex situ SSRTs showed almost the same tensile properties as air and a limited brittle fracture confined to near the surface. In contrast, the in situ SSRTs showed an abrupt failure after the maximum tensile load, leading to a brittle fracture across the entire fracture surface with stress-oriented hydrogen-induced cracking (SOHIC). The crack trace analysis results indicated that SOHIC propagation paths were influenced by localized hydrogen accumulation due to high-stress fields. As a result, the dominant hydrogen embrittlement mechanisms, such as hydrogen-enhanced localized plasticity (HELP) and hydrogen-enhanced decohesion (HEDE), changed. These findings provide critical insights into the microstructural factors affecting hydrogen embrittlement, which are essential for the design of hydrogen-resistant steels in hydrogen infrastructure applications.
This study explored the influence of hydrogen on the tensile properties and fracture behavior of high-strength API X70 and X80 linepipe steels with bainitic microstructures under varying hydrogen charging conditions. The X70 steel exhibited a ferritic microstructure with some pearlite, while the X80 steel showed a bainitic microstructure and fine pearlite due to the addition of molybdenum. Slow strain rate tests (SSRTs) were conducted using both electrochemical ex situ and in situ hydrogen charging methods subjected to different current densities. The SSRT results showed that in situ hydrogen-charged SSRT, performed at current densities above 1 A/m2, led to more pronounced hydrogen embrittlement compared to ex situ hydrogen-charged SSRT. This occurred because hydrogen was continuously supplied during deformation, exceeding the critical concentration even in the center regions, leading to quasi-cleavage fractures marked by localized cleavage and tearing ridges. Thermal desorption analysis (TDA) confirmed that a greater amount of hydrogen was trapped at dislocations during in situ hydrogen-charged SSRT, intensifying hydrogen embrittlement, even with a shorter hydrogen charging duration. These findings highlight the importance of selecting appropriate hydrogen charging methods and understanding the hydrogen embrittlement behavior of linepipe steels.
In this study, the effect of subsequent heat treatment applied to high-strength low-alloy steel (HSLA) on the structure–property relationships was investigated. Tempering and intercritical annealing processes are introduced to elucidate the influence of subsequent heat treatment on mechanical properties of direct-quenched Fe-0.06C-0.2Si-2.0Mn steel from a microstructural perspective. The tempering process results in a typical tempered martensite with uniformly dispersed cementite, whereas the intercritical annealing process forms a dual-phase microstructure composed of soft ferrite and hard martensite for the direct-quenched steel. In the intercritical annealed steel, a number of mobile dislocations at the interphase (martensite/ferrite) boundary significantly decrease the yield strength, and the large difference in strength between ferrite and martensite enhances work hardening. Charpy V-notch impact test results indicate that the tempering and intercritical annealing processes improved the absorbed energy by more than 100 J compared to the direct-quenched steel at room temperature, and at −50 °C, the intercritically annealed steel exhibited the highest absorbed energy of approximately 140 J. Additionally, the high fraction of high-angle grain boundaries and fine grains of the intercritically annealed steel increase the resistance to cleavage crack propagation, thereby reducing the ductile-to-brittle transition temperature.
8 April 2024 in Archives of Metallurgy and Materials
This study describes how microstructural constituents affected the hydrogen embrittlement resistance of high-strength pipeline steels. The American Petroleum Institute (API) X60, X70, and X80 pipeline steels demonstrated complicated microstructure comprising polygonal ferrite (PF), acicular ferrite, granular bainite (GB), bainitic ferrite (BF), and secondary phases, e.g., the martensite-austenite (MA) constituent, and the volume fraction of the microstructures was dependent on alloying elements and processing conditions. To evaluate the hydrogen embrittlement resistance, a slow strain rate test (SSRT) was performed after electrochemical hydrogen charging. The SSRT results indicated that the X80 steel with the highest volume fraction of the MA constituent demonstrated relatively high yield strength but exhibited the lowest hydrogen embrittlement resistance because the MA constituent acted as a reversible hydrogen trap site.
21 June 2024 in Archives of Metallurgy and Materials
This study describes how microstructural constituents affected the hydrogen embrittlement resistance of high-strength pipeline steels. The American Petroleum Institute (API) X60, X70, and X80 pipeline steels demonstrated complicated microstructure comprising polygonal ferrite (PF), acicular ferrite, granular bainite (GB), bainitic ferrite (BF), and secondary phases, e.g., the martensite-austenite (MA) constituent, and the volume fraction of the microstructures was dependent on alloying elements and processing conditions. To evaluate the hydrogen embrittlement resistance, a slow strain rate test (SSRT) was performed after electrochemical hydrogen charging. The SSRT results indicated that the X80 steel with the highest volume fraction of the MA constituent demonstrated relatively high yield strength but exhibited the lowest hydrogen embrittlement resistance because the MA constituent acted as a reversible hydrogen trap site.
23 November 2022 in Archives of Metallurgy and Materials
In this study, the effect of the coiling temperature on the tensile properties of API X70 linepipe steel plates is investigated in terms of the microstructure and related anisotropy. Two coiling temperatures are selected to control the microstructure and tensile properties. The API X70 linepipe steels consist mostly of ferritic microstructures such as polygonal ferrite, acicular ferrite, granular bainite, and pearlite irrespective of the coiling temperature. In order to evaluate the anisotropy in the tensile properties, tensile tests in various directions, in this case 0° (rolling direction), 30°, 45° (diagonal direction), 60°, and 90° (transverse direction) are conducted. As the higher coiling temperature, the larger amount of pearlite is formed, resulting in higher strength and better deformability. The steel has higher ductility and lower strength in the rolling direction than in the transverse direction due to the development of γ-fiber, particularly the {111} texture.