Neel Kamal Gupta

Dr. Neel Kamal Gupta

orcid

Research Focus & Metrics

Academic Career Length

3Years (2024-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
10 October 2024 in Applied Sciences
Verified
Journal Article
Open access
PDF file
ASAbid Shah
Abid Shah
NGNeel Kamal Gupta
Neel Kamal Gupta
RARezo Aliyev
Rezo Aliyev
HZHenning Zeidler
Henning Zeidler
Copper-based alloys are widely known for their high thermal and electrical conductivity. Although the use of these alloys in powder-based additive manufacturing (AM) shows significant promise, applying this method in wire arc additive manufacturing (WAAM) processes poses various considerable challenges, including porosity, delamination, surface oxidation, etc. The limited research on WAAM of copper alloys, especially Cu1897, highlights the need for a more in-depth investigation. This study addresses the effects of process parameters in pulse cold metal transfer (CMT)-based WAAM of Cu1897, i.e., pulse correction (PC) and arc length correction (ALC), on bead penetration and porosity. The results showed that as PC was increased from −5 to +5, weld bead penetration increased from 2.38 mm to 3.87 mm. To further enhance penetration and reduce the porosity, the ALC was varied from +30% to −30% with a step size of 15%. The results showed that weld bead penetration increased to 4.47 mm by altering the ALC from +30% to −30%. Additionally, as the ALC varied within this range, porosity decreased significantly from 3.98% to 0.28%. Overall, it is concluded that a lower value of ALC is recommended to improve bead penetration and reduce porosity in WAAM of Cu1897.

Verified
Journal Article
Open access
PDF file
GGGanesan G
Ganesan G
NGNeel Kamal Gupta
Neel Kamal Gupta
SSS. Siddhartha
S. Siddhartha
SKShahu Rajaram Karade
Shahu Rajaram Karade
HZHenning Zeidler
Henning Zeidler
KKK. P. Karunakaran
K. P. Karunakaran
This study investigates the influence of varying layer thickness through interlayer machining in Wire Arc Additive Manufacturing (WAAM) and its impact on microstructural evolution, mechanical properties, and residual stress distribution. It compares four types of WAAM samples: As-built with uneven layer thickness without interlayer machining and uniform layer thicknesses of 2 mm, 1.5 mm, and 1 mm achieved through interlayer machining. As-built components exhibited coarse columnar grains and uneven deposition, adversely affecting hardness and strength. Interlayer machining at reduced layer thickness refined grains, restricted growth, and induced plastic deformation, leading to enhanced mechanical properties. Grain refinement achieved reductions of 62.7% (top), 77.6% (middle), and 64.3% (bottom), significantly improving microstructural uniformity. Microhardness increased from 150 to 180 HV (as-built) to 210 to 230 HV (machined to maintain 1 mm layer thickness), marking a 40–43% improvement. Tensile strength was enhanced, with UTS increasing from 494.72 MPa to 582.11 MPa (17.6%) and YS from 371 MPa to 471 MPa (26.9%), although elongation decreased from 59% to 46% (22% reduction). Residual stress was reduced by 55–60%, improving structural integrity. These findings highlight interlayer machining as a key strategy for optimizing WAAM-fabricated components while balancing mechanical performance and manufacturing efficiency.

15 January 2025 in Metals
Verified
Journal Article
Open access
PDF file
SKShahu Rajaram Karade
Shahu Rajaram Karade
SSSiddhartha Siddhartha
Siddhartha Siddhartha
NGNeel Kamal Gupta
Neel Kamal Gupta
GGGanesan G
Ganesan G
KKK. P. Karunakaran
K. P. Karunakaran
HZHenning Zeidler
Henning Zeidler
Additive manufacturing (AM) has evolved to enable the direct production of functional components through the hybridization of additive and subtractive processes. In metal wire AM, hybridization is key, encompassing process integration (addition/subtraction), energy source combinations (arc/laser), kinematic options (3/4/5 axis), and slicing techniques (planar/conformal). This paper focuses on these hybridization methods, with a unified system designed for single-machine setups, improving efficiency and accuracy. This study presents a detailed exploration of these hybridization levels through the fabrication of a complex 5-axis geometry—an impeller. The impeller was manufactured with hybridization using various levels and subsequently compared with manufacturing processes like additive manufacturing with interlayer machining and traditional machining methods. The hybrid approach significantly reduced the manufacturing time for the selected impeller geometry from 3536 min to 792 min (saving 77.6% manufacturing time) and minimized material waste to 9.3%, compared with 74.07% in traditional machining. This demonstrates a more efficient, precise, and cost-effective method to optimize metal wire AM for producing complex metal components, advancing capabilities and applications.

6 February 2024 in Journal of Micromanufacturing
Verified
Journal Article
Closed access
NGNeel Kamal Gupta
Neel Kamal Gupta
PRPawan Kumar Rakesh
Pawan Kumar Rakesh
VRVikas Rastogi
Vikas Rastogi
ISInderdeep Singh
Inderdeep Singh
Additive manufacturing has been a revolution in the last decade and has led to a number of product innovations. Rapid prototyping (RP) has significantly reduced the product development cycle time and RP techniques are now replacing many conventional plastic processing techniques where production volume is not an issue. In order to ascertain the utility of additive manufacturing techniques for the development of fully functional parts, it’s important to establish the optimal set of process parameters for achieving maximum mechanical performance. In the current experimental investigation, the dogbone-shaped parts of acrylonitrile butadiene styrene (ABS) were fabricated by the fused deposition modeling (FDM) process. The process parameters were optimized for dogbone-shaped specimens fabricated by the FDM process. Among the parameters, it has been found that orientation and infill density are the most dominant factors affecting the tensile strength of FDM parts printed with ABS material.

23 April 2025 in Propellants, Explosives, Pyrotechnics
Verified
Journal Article
Open access
Gromov Alexandrovich GromovGromov Alexandrovich Gromov
Gromov Alexandrovich Gromov
KMKonstantin Matrosov
Konstantin Matrosov
RARezo Aliyev
Rezo Aliyev
NGNeel Kamal Gupta
Neel Kamal Gupta
This study is devoted to the investigation of combustion characteristics of aluminized solid propellants (SPs) with ammonium nitrate (SP4, 44 wt.% and SP5, 66 wt.%), ammonium perchlorate (5 wt.%), and inert (butyl rubber) and active (polyvinyl tetrazole) binders. The experimental SP formulations were compared with their analogs, both with and without ammonium nitrate included in their compositions. Among ammonium nitrate–contained SPs, the following row of burning rates was found (ammonium nitrate content in brackets, wt.%): SP3 (0) > SP2 (44) ∼ SP4 (44) > SP1 (51) > SP5 (66).The studied SPs were modified by additives of micron‐sized oxide powders (Co3O4, V2O5, MnO2, Fe2O3, CuO) and bichromate salts (K2Cr2O7, Na2Cr2O7, (NH4)2Cr2O7) or potassium bichromate in combination with the second salt of different origin: oxalates (NH4)2C2O4, La2(C2O4)3, and Na2C2O4 and chlorides NaCl, KCl, and BaCl2.Micron‐sized oxide powders were added into the formulation SP4 with 44 wt.% of ammonium nitrate. It was found that there was a 20–30% improvement in the burning rate. CuO exhibited the most pronounced catalytic effect, increasing the burning rate by up to 270% compared to the SPs without additives. K2Cr2O7 was the effective combustion modifier for ammonium nitrate–based SPs, enhancing the burning rate by up to 100% in the pressure range above 4 MPa. The addition of BaCl2 and La2(C2O4)3 in the pressure range from 2 to 5 MPa had a promoting effect on K2Cr2O7.The studied salt mixtures based on K2Cr2O7 were found to be effective catalysts for AN‐based SP combustion.

11 February 2026 in Progress in Additive Manufacturing
Verified
Journal Article
Open access
PDF file
BGBahar Gharehpapagh
Bahar Gharehpapagh
RARezo Aliyev
Rezo Aliyev
NGNeel Kamal Gupta
Neel Kamal Gupta
MMMagdalena Milek
Magdalena Milek
HZHenning Zeidler
Henning Zeidler
Glass offers unique advantages such as high optical transparency, thermal stability, and chemical resistance, making it indispensable in optics, microelectronics, sensing, and biomedical applications. However, its high melting point, brittle nature, and incompatibility with traditional manufacturing methods present significant fabrication challenges. Additive manufacturing (AM) introduces new possibilities for the glass industry by enabling the fabrication of customised, complex 3D structures and the integration of glass with other compatible materials. In particular, multi-material glass additive manufacturing (MMGAM) has emerged as a promising frontier, enabling both the spatial tuning of glass composition, dopants, and functionalities, as well as the co-fabrication of glass with dissimilar materials, such as polymers, metals, or ceramics, within a single component using integrated AM platforms. This paper provides a comprehensive overview of the current state of MMGAM, structured around four key themes: (i) key material properties and interfacial compatibility considerations, (ii) AM techniques adapted for multi-material glass systems, (iii) material combinations and strategies for functional integration, and (iv) future challenges and research directions. Particular emphasis is placed on the challenges of interfacial bonding, material compatibility, and the formulation of printable glass systems suitable for co-processing with other materials. The review explores recent strategies for enabling multifunctional, integrated architectures that combine optical, structural, or chemical functionalities within a single component. By synthesising current advances and outlining key research gaps, this work aims to accelerate the development and broader adoption of MMGAM technologies.