The production process requires massive amounts of minerals, fossil fuels, and energy. The efficient use of energy and natural resources appears to be crucial to the state of affairs. It should be noted that the post-consumer management of solar power plant elements results in a certain amount of power and matter, as well as harmful effects on the natural world. The major goal of this study was to examine the environmental effect of the solar power plant throughout its life cycle, taking into consideration the depletion of natural materials and mineral resources, using the ReCiPe 2016 model. A life cycle study was performed on an actual 2 MW solar power facility located in northern Poland. This study was conducted using the ReCiPe 2016 model and the Life Cycle Assessment (LCA) methodology. The analyzed renewable energy system’s impact was assessed utilizing 22 impact categories, focusing mostly on the depletion of natural resources. A Life Cycle Assessment was conducted for two post-consumer development scenarios (landfill and recycling). This research focuses on the full solar power plant, not just the photovoltaic panels. Recycling, as a kind of post-consumer development, can provide major environmental benefits and minimize negative environmental consequences throughout the solar power plant’s life cycle. The exceedingly harmful effects can be evident in losses related to water and the aquatic environment. The obtained study findings enabled the development of sustainable-friendly recommendations towards the continuous advancement of the life cycle of solar power plants, thereby reducing the use of rare earth minerals.

The main objective of this study is to assess the environmental life cycle of the materials, components, and elements of a mono-Si photovoltaic power plant towards their sustainable development. Currently, photovoltaic installations are considered to be environmentally friendly systems that produce “green” energy. During their exploitation, no pollutants are emitted into the environment. However, the processes of manufacturing and post-used management of their materials, components and elements are associated with both high demand for energy and matter, as well as with emissions of harmful substances into the atmosphere, water, and soil. For this reason, from the perspective of the entire life cycle, photovoltaic power plants may contribute to the deterioration of human health, the reduction in the quality of the environment, and the depletion of non-renewable fossil resources. Due to these potential threats, it was considered appropriate to conduct a Life Cycle Assessment of a real 2 MW photovoltaic power plant located in northern Poland, in terms of compliance with the main assumptions of sustainable development. The analysis was conducted using the Life Cycle Assessment (LCA) methodology (the ReCiPe 2016 model). Impacts on the environment was assessed in three areas: human health, ecosystem quality, and material resources. Two scenarios were adopted for the post-used management of materials, components, and elements: landfill disposal and recycling. Based on the conducted research, it was found that, among the assessed groups of photovoltaic power plant components (photovoltaic modules, supporting structure, inverter station, and electrical infra-structure), photovoltaic modules have the highest level of harmful impact on the environment (especially the manufacturing stage). The use of recycling processes at the end of their use would reduce their harmful impact over the entire life cycle of a photovoltaic power plant and better fit with the main principles of sustainable development.

Currently, silicon is the most often utilized material for photovoltaic cell manufacturing, as it has the potential to convert solar energy directly into electricity. The silicon used in photovoltaic solutions must be highly pure. Large amounts of power, raw materials, and fossil fuels are consumed in the production process. Post-consumer treatment of polymers, materials, and components also requires energy and matter. These processes have a significant influence on the environment. As a result, the primary purpose of this article is to evaluate the influence of a photovoltaic power plant’s material and component life cycle on ecosystem quality. The research focuses on an actual photovoltaic power plant with a capacity of 2 MW located in northern Poland. According to the findings, photovoltaic modules are the part that has the most negative environmental impact, since their manufacturing requires a substantial amount of materials and energy (primarily from conventional sources). Post-consumer management, in the form of recycling after use, would provide major environmental advantages and reduce detrimental environmental consequences throughout the course of the solar power plant’s full life cycle.

The friction coefficient of articular cartilage (AC) is very low. A method of producing tailor-made materials with even similar lubrication properties is still a challenge. The physicochemical reasons for such excellent lubrication properties of AC are still not fully explained; however, a crucial factor seems to be synergy between synovial fluid (SF) components. As a stepping stone to being able to produce innovative materials characterized by a very low friction coefficient, we studied the interactions between two important components of SF: human serum albumin (HSA) and chondroitin sulfate (CS). The molecular dynamics method, preceded by docking, is used in the study. Interactions of HSA with two types of CS (IV and VI), with the addition of three types of ions often found in physiological solutions: Ca${}^{2+}$, Na${}^{+}$, and Mg${}^{2+}$, are compared. It was found that there were differences in the energy of binding values and interaction maps between CS-4 and CS-6 complexes. HSA:CS-4 complexes were bound stronger than in the case of HSA:CS-6 because more interactions were formed across all types of interactions except one—the only difference was for ionic bridges, which were more often found in HSA:CS-6 complexes. RMSD and RMSF indicated that complexes HSA:CS-4 behave much more stably than HSA:CS-6. The type of ions added to the solution was also very important and changed the interaction map. However, the biggest difference was caused by the addition of Ca${}^{2+}$ ions which were prone to form ionic bridges.

The aim of the study was to assess the mechanical and material properties of porous titanium capsules, produced by 3D printing via the DMLS (Direct Metal Laser Sintering) technique based on their potential application as carriers for anticancer drugs. The study used capsules made from the Ti-6Al-4V alloy, and analyzes the impact of geometric parameters, structural features, and printing angles (0°, 45°, and 90°) on their compressive strength. A total of 36 capsules were tested, 18 of type KTD and 18 of type KTM, each in two loading directions. The surface roughness and damage characteristics resulting from mechanical loading have also been evaluated. Statistical analysis of the results was performed using Student’s t-test. The results show that the capsules printed at an angle of 45° are characterized by the highest compressive strength, while their resistance significantly exceeds the values typical of human bone tissue. Additionally, the observed damage does not lead to the formation of sharp edges or loose fragments, which confirms the safety of their use in the body. The high surface roughness promotes tissue integration and limits capsule migration after implantation. The analyses confirm the potential of 3D-printed titanium capsules as effective and safe drug carriers in personalized anticancer therapy.

Metal powder 3D printing technology is gaining popularity due to the possibility of producing structural elements of complex geometry, which production with the methods used so far is difficult or impossible to obtain. An example of a material used in the parts production by the additive method is 316L steel, which is used in the production of bone support screws, surgical tools and needles, or in other industries for the production of exhaust manifolds, parts of furnaces or heat exchangers. The study investigated the mechanical properties, hardness and microstructure of 316L steel produced in the selective laser melting process (SLM). Based on the tests, the following mechanical properties of 316L steel were obtained: Su = 566.7MPa, Sp0.2 = 484MPa, E = 113820MPa, A = 79.5%, Z = 72.3%. The hardness test results show a significant increase in hardness as the tensile test approaches the sample fracture. The structure of 316L steel in the grip part is characterized by the formation of visible semi-elliptical zones of the material alloy, the pools with crystallized grains with a cell-column structure oriented in the direction of the thermal gradient. This type of microstructure is characteristic of technology in which, after solidification, the cooling process takes place at high speed.