This work presents a high-efficiency low-noise propeller design for unmanned aerial vehicles. Three different blade configurations are first investigated, using the computational aeroacoustic approach to recognize the flow around propellers and the noise emissions. The flow simulation is obtained by an acoustic-wave preserved artificial compressibility method, and the far-field noise is extrapolated by solving the Ffowcs-Williams and Hawkings equations. Experiments are also conducted to validate numerical simulations and the design philosophy. The comparison between numerical and experimental results confirms an encouraging agreement regarding aerodynamic efficiency, noise spectra and differences between propellers. The results show that two designed propellers can simultaneously improve aerodynamic efficiency and reduce noise emissions compared to the baseline propeller. It is observed that using a longer chord length and shorter propeller radius can reduce flow separation at the trailing edge. Furthermore, a qualitative noise-source analysis shows that broadband noise sources are primarily ascribed to the time-derivative of blade surface pressure and occur at the trailing edge near the tip.
1 May 2020 in The Journal of the Acoustical Society of America
A wavelet-based beamforming method is performed in this investigation to analyze moving acoustic sources in the time-frequency domain, which is of scientific significance and practical importance. The particular problem considered here is the interaction noise from an airfoil and the downstream rotor in the presence of a moving flow, which could find realistic applications in next-generation underwater and aviation systems. A realistic experimental setup is prepared with a rotating blade and the airfoil in an anechoic wind tunnel. The results show that the wavelet-based beamforming method is very suitable for unsteady sound source imaging, which would be able to strengthen the time-frequency analysis capability of acoustic imaging tests and, consequently, possibly leads to deepened physical insights of various transient and moving systems in underwater and aerospace systems.
1 January 2022 in Aerospace Science and Technology
Unmanned aerial vehicles (UAVs) have become an important research topic due to their wide range of applications and potential to meet the future air transportation demands. In many configurations of UAVs, the rotors interact with the wake of upstream bodies, which is of pivotal importance to the aerodynamic and aeroacoustic performance. The studies of flow structures and noise sources for rotors interacting with adjacent upstream bodies at Reynolds numbers lower than 105, which is the operating condition of most small UAVs, are limited. In the current study, numerical simulations are conducted to investigate the interaction between a rotor and the wake of an airfoil at low Reynolds numbers around 104 using the Spalart–Allmaras delayed detached eddy simulation method and acoustic analogy based on Farassat's formulation 1 A. The results show that the axial forces and the surface pressure perturbations of the airfoil are closely coupled with the rotor rotation. The effect of interaction on the rotor blades depends on the relative angle of attack. Furthermore, an analysis of the surface pressure fluctuations corresponding to the noise sources shows that the tonal noise at the blade passing frequency and its harmonics is mainly caused by periodical interaction, and the high-frequency noise is produced by the shedding vortex at the trailing edge of the rotor.
Ducted propellers present broad applicability in urban air mobility vehicles due to their enhanced operational safety, improved aerodynamic performance, and potential to mitigate noise emissions. This study proposes a numerical approach for designing adequate duct geometries, focusing on the duct's lip profile, expansion ratio, and tip clearance, aiming to provide valuable design guidance for ducted propellers. The simulations are validated through experimental data, showing reasonable agreement in terms of thrust generation and far-field noise. The mean flow and generated thrust are characterized with a parametric study using steady simulations, while delayed detached eddy simulations are employed to capture transient flow characteristics and investigate noise generation. The noise levels were computed using the integral solution of the Ffowcs-Williams and Hawkings equation. The lip geometry impacts the flow distribution and generated thrust, modifying the tonal noise. Furthermore, slightly divergent ducts can increase the total thrust by minimizing flow separation on the duct wall while increasing the suction on the duct lip. The primary noise sources are identified at the propeller's leading edge and tip. The results reveal that divergent ducts effectively reduce tonal noise at all observer angles but increase broadband noise, attributed to the noise sources at the leading edge of the propeller and the interaction with the duct lip. Additionally, reducing the tip clearance from 2 to 1 mm enhances the total thrust by more than 20% without causing extra noise generation.