Halide perovskite-based memristors are promising neuromorphic devices due to their unique ion migration and interface tunability, yet their conduction mechanisms remain unclear, causing stability and performance issues. Here, we engineer interstitial Ag+ ions within a quasi-two-dimensional (quasi-2D) halide perovskite ((C6H5C2H4NH3)2Csn−1PbnI3n+1) to enhance device stability and controllability. The introduced Ag+ ions occupy organic interlayers, forming thermodynamically stable structures and introducing deep-level energy states without structural distortion, which do not act as non-radiative recombination centers, but instead serve as efficient charge trapping centers that stabilize intermediate resistance states and facilitate controlled filament evolution during resistive switching. This modification also leads to enhanced electron transparency near the Fermi level, contributing to improved charge transport dynamics and device performance. Under external electric fields, these Ag+ ions act as mobile ionic species, facilitating controlled filament formation and stable resistive switching. The resulting devices demonstrate exceptional performance, featuring an ultrahigh on/off ratio (∼108) and low operating voltages (∼0.31 V), surpassing existing benchmarks. Our findings highlight the dual role of Ag+ ions in structural stabilization and conduction modulation, providing a robust approach for high-performance perovskite memristor engineering.
6 August 2024 in Superconductor Science and Technology
We report on the fabrication, structural, and electrical transport characterizations of superconducting nanowire arrays based on nano-laser direct writing (NLDW). The thermal excitation-induced micro/nano fabrication based on the interactions between NLDW and superconducting Nb films was experimentally analyzed and simulated. Experimentally, the arrays of superconducting nanowires have an area of 190 × 190 with a critical transition temperature Tc of 7.8 K and a critical current density Jc of 20.8 MA cm−2 at 4.0 K. The width and arrangement of the nanowires are precisely controlled, exhibiting a minimal loss of 0.6 K in Tc and excellent Jc after LDW. The width of superconducting nanowires could be further optimized by adjusting parameters such as laser power, irradiation gap, and delay of points. Compared with electron beam lithography and focused ion beam, to some extent, the nanowires fabrication process based on NLDW provides a more efficient and cost-effective path for fabricating large-area superconducting circuits and devices.
To realize large-scale micro/nanofabrication process in superconducting devices, the nano laser direct writing (NLDW) as a potential tool was implemented. In this paper, thermal effect induced laser-matter (superconducting film) interaction based on laser direct writing on Nb films and laser exposure on photoresist were investigated by simulation and experiment. To avoid nanoscale thermal effect on superconducting films, large-scale superconducting nanoarrays with the area up to 100 µm × 100 µm based on laser exposure on photoresist were fabricated. Compared with laser direct writing on superconducting films, which lead to the degradation of superconducting performance such as critical current, transition temperature, the superconducting nanoarrays based on laser exposure on photoresist maintain excellent superconducting performance without degradation. Besides that, by further optimizing the process parameters and the thickness of photoresist, the nanowires with the width down to nanometers are plausible. Compared with the traditional electron beam and ion beam process, to some extent, the nanowires fabrication process based on NLDW provides a more efficient and cost-effective path for the fabrication of large-area superconducting devices/circuits.
We report the evolution of electric transport of Nb bridges based on nanoscale thermal effects created by nanolaser direct writing (NLDW) on Nb films. The laser–Nb-film interaction was investigated experimentally and by simulation. We demonstrate laser parameters such as irradiation power and interaction time to manipulate the electric transport of Nb bridges, such as the critical current and transition temperature, via simulation, which align with the electron probe microanalyzer results. Based on the optimized laser parameters, we realize the continual changes in current–voltage characteristics via increasing irradiation power. Furthermore, Nb bridges after laser irradiation show the oscillations of the critical current when we apply the coil current under a magnetic field that is perpendicular to the Nb bridges, which is similar to the Fraunhofer pattern in a Josephson junction under a magnetic field. In this case, NLDW shows the potential to manipulate electrical performances, which could be used to trim tri-layer junctions, tune shunt resistors, adjust critical currents or even induce a Josephson junction in situ by further shrinking of the laser spot.
We report the thermal excitation-induced material modification and micro/nano fabrication based on the interactions between nano laser direct writing (NLDW) and superconducting films experimentally and by simulation. The niobium (Nb) films with a critical temperature of 9 K were deposited on silicon substrate via sputtering with the thickness of around 50 nm. The boundary between material modification and micro/nano fabrication was verified by changing the interaction time and laser power continuously. Specifically, as the laser power was fixed at 250 mW and the interaction time below 440 ns, the interaction is material modification. With the increasing interaction time further, the Nb films were etched away. As the interaction time was fixed at 500 ns and the laser power below 200 mW, the interaction is material modification too. With the increasing of laser power further, the Nb films were etched away. In the experiment, the oxygen content and current–voltage characteristic (IVCs) before and after laser irradiation were displayed to verify the material modification, which is in line with the simulation results. Considering the 50 nm resolution of NLDW, in the material modification region, one could trim trilayer junctions, tune shunt resistors, or adjust critical currents, etc. In the micro/nano fabrication region, one could fabricate various devices and exploit the properties of high spatial resolution, high flexibility, and fast processing.
The Josephson junction, a key component of superconducting quantum circuits, is much less mature, especially for the high-transition (high-Tc) temperature cuprate superconductors. Herein, we report on the realization of high-Tc Josephson junction based on nanoslits on a SrTiO3 substrate. We demonstrate the ability to manipulate the current–voltage characteristics of YBa2Cu3O7−x bridges continuously from superconducting current-dominated to Josephson junction behavior by changing the irradiation parameters of the focused Ga+ ion beam on a single-crystal SrTiO3 substrate. The periodic critical current that depends on the magnetic flux coupled into the superconducting quantum interference devices was observed, which exactly reflects the effects of quantum tunneling and flux quantization. To some extent, this weak link within the framework of the semiconductor manufacturing process shows the potential to provide a cost-effective, highly efficient, and reliable pathway for scaling up quantum mechanical superconducting circuits, which is promising for the fabrication process.