Chien-Hung Lai

Prof. Dr. Chien-Hung Lai

orcid

Research Focus & Metrics

Academic Career Length

9Years (2018-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
4 January 2022 in IEEE Access
Verified
Journal Article
Open access
JCJiann-Jong Chen
Jiann-Jong Chen
Yuh-Shyan HwangYuh-Shyan Hwang
Yuh-Shyan Hwang
WJWei-Ming Jiang
Wei-Ming Jiang
CLChien-Hung Lai
Chien-Hung Lai
JKJoshua Ku
Joshua Ku
This paper presents a new improved ultra-fast-response low-transient-voltage buck converter with transient-acceleration loops and V-cubic techniques. Firstly, the proposed buck converter is based on optimum-damping control, so it is necessary to add a slope-compensation circuit to accelerate the transient response and decrease the transient voltage. Secondly, the proposed converter utilized the adaptive on-time controlled and V-cubic techniques to stabilize the switching frequency and promote the conversion efficiency. Thirdly, we utilized a rail-to-rail operational transconductance amplifier, which was used as a current-sensing circuit, to reach the feature of wide input range, so that it can directly sense the voltage without voltage dividing resistors. The rapid transient response and small transient voltage can be obtained when the load current changes. The proposed converter is fabricated with TSMC $0.18~\mu \text{m}$ 1P6M process. The switching frequency is 3 MHz. The total area of the chip is 1.44 mm2 (with PADs). The measured results are as follows. When the load current varies between 50 mA and 500 mA, the fastest recovery time is only $1.6 ~\mu \text{s}$ , and the overshoot and undershoot are both 20 mV. The maximum efficiency is 90.1%.

23 April 2021 in IEEE Transactions on Very Large Scale Integration (VLSI) Systems
Verified
Journal Article
Closed access
JCJiann-Jong Chen
Jiann-Jong Chen
Yuh-Shyan HwangYuh-Shyan Hwang
Yuh-Shyan Hwang
JWJyun-Heng Wu
Jyun-Heng Wu
CLChien-Hung Lai
Chien-Hung Lai
YKYi-Tsen Ku
Yi-Tsen Ku
The converter proposed in this article is a new improved voltage-square buck converter using a rail-to-rail OTA-based current-sensing circuit. This circuit architecture used a constant on-time modulation mode and uses a rail-to-rail OTA-based inductor-current-sensing circuit to form a current feedback path. The rail-to-rail OTA-based current sensor has wide input range, so it can be directly connected to both the ends of the inductor. Then, a voltage loop is added to achieve fast transient response and reduce the output voltage ripple. Therefore, the proposed voltage-square buck converter responses to load current change immediately by two voltage and one current feedback signals. The converter is implemented with TSMC 0.35- μm CMOS 2P4M process, and the chip area is 2.24 mm. 2 The input voltage range is 3-3.6 V. When the output voltage is 2.5 V and the output current is 350 mA, the circuit has the maximum efficiency of 91%. The contributions of this article are listed in the following: 1) we have proposed a new improved V 2 control architecture of power converters, which combined current-mode control and voltage-mode control; 2) the proposed architecture has one current control loop and two voltage control loops, which can balance the output voltage and output current; 3) the proposed converter has the characteristics of faster transient response and lower transient voltage; 4) we designed, measured, and implemented this proposed converter; and 5) from the FOM formula, the performance of the proposed converter is found to be better than other recent works.

13 September 2021 in IEEE Access
Verified
Journal Article
Open access
Yuh-Shyan HwangYuh-Shyan Hwang
Yuh-Shyan Hwang
JCJiann-Jong Chen
Jiann-Jong Chen
JXJing-Xiang Xu
Jing-Xiang Xu
HYHao-Shun Yang
Hao-Shun Yang
CLChien-Hung Lai
Chien-Hung Lai
YKYi-Tsen Ku
Yi-Tsen Ku
This paper proposes a new and improved fast-transient-response low-transient-voltage boost converter with pseudo-current hysteresis-controlled techniques (PCHC). The converter uses the rail-to-rail current-sensing circuit to provide a hysteresis-controlled signal, helping to speed up the transient response and improve the overall efficiency. The proposed boost converter has been fabricated with TSMC $0.18~\mu \text{m}$ CMOS 1P6M technology, and the chip area is $1.18\times 1.18$ mm 2 (include PADs). The measured results show that the input voltage range is from 0.5 V to 1 V, the output voltage is set as 1.8 V, and the output load current range is from 10 mA to 100 mA. When the output load current changes from 10 mA to 100mA and 100 mA to 10 mA, the transient responses are both 2 $\mu \text{s}$ , and peak power efficiency is 88.5% at the output load current of 75 mA.

10 March 2022 in IEEE Sensors Journal
Verified
Journal Article
Closed access
JCJiann-Jong Chen
Jiann-Jong Chen
Yuh-Shyan HwangYuh-Shyan Hwang
Yuh-Shyan Hwang
SHSzu-Hsien Ho
Szu-Hsien Ho
CLChien-Hung Lai
Chien-Hung Lai
YKYi-Tsen Ku
Yi-Tsen Ku
This paper proposed an improved low-electromagnetic-interference (EMI), high-efficiency fast-transient-response buck converter suitable for wireless sensor networks with new transient accelerated techniques. The proposed second-order delta-sigma modulator used the noise-shaping technique and the oversampling theorem to reduce the electromagnetic interference of the output spectrum. And then added the transient acceleration loop to accelerate the transient response also lowers the undershoot and overshoot voltage when the load current changed. The proposed converter has been implemented with TSMC $0.18~\mu \text{m}$ 1P6M process, and the chip area is $1.19 \times 1.19$ mm 2 (including PADs). The measured results show that when the output voltage is 2 V and the load current changes from 100 mA to 500 mA and from 500 mA to 100 mA, the transient responses are $4 ~\mu \text{s}$ and $3 ~\mu \text{s}$ , and transient voltages are 18 mV and 30 mV, respectively. Compared to the traditional continuous-time delta-sigma-modulation converter improved $3 ~\mu \text{s}$ and $7 ~\mu \text{s}$ . The maximum output voltage ripple is 30 mV. The output-to-noise ratio (ONR) is 72.15 dB with the sampling frequency of 10 MHz. When the load current is 100 mA and the output voltage is 2.5 V, the peak efficiency is 90.8%.

8 January 2021 in IEEE Transactions on Industrial Electronics
Verified
Journal Article
Closed access
JCJiann-Jong Chen
Jiann-Jong Chen
Yuh-Shyan HwangYuh-Shyan Hwang
Yuh-Shyan Hwang
YKYi-Tsen Ku
Yi-Tsen Ku
CLChien-Hung Lai
Chien-Hung Lai
In this article, we propose a new improved fast-transient-response and low-noise high-efficiency buck converter with second-order continuous-time delta-sigma-modulation (CT-DSM) techniques. First, by utilizing the oversampling theorem and noise-shaping technique with the second-order delta-sigma modulation, the output noise within the bandwidth can be reduced effectively. Second, the adding of the transient acceleration loop not only can improve the transient recovery time when the load current changed but also lowers the undershoot and overshoot voltage. Third, a rail-to-rail operational transconductance amplifier without voltage dividers is employed in the proposed converter, which helps sensing the inductor current, moving the inductor pole to a high frequency, speeding up the transient response, and stabilizing the proposed converter modules. Finally, the proposed converter has been implemented with TSMC 0.18 μm 1P6M process and occupies an area of 1.19 × 1.19 mm 2 . When the load current changed from 50 to 500 mA and 500 to 50 mA, the transient recovery time was both 4 μs, which improved 8 and 16 μs than the traditional CT-DSM converter. The output voltage ripples are kept under 13 mV and the overshoot and undershoot voltage is 20 and 14 mV, respectively. The measured output-to-noise ratio is 80.7 dB, with the sampling frequency of 10 MHz. The peak efficiency is 92.1%, at the output voltage of 2.5 V and load current of 150 mA.

24 April 2023 in IEEE Access
Verified
Journal Article
Open access
JCJiann-Jong Chen
Jiann-Jong Chen
Yuh-Shyan HwangYuh-Shyan Hwang
Yuh-Shyan Hwang
HCHung-Wei Chiu
Hung-Wei Chiu
MLMing-Dao Luo
Ming-Dao Luo
CLChien-Hung Lai
Chien-Hung Lai
JKJoshua Ku
Joshua Ku
This paper proposed a new low-noise I-squard 2 nd -order continuous-time-delta-sigma-modulation (CT-DSM) buck converter suitable for wireless sensor networks with dual-current-acceleration (DCA) techniques. First, it adopts the second-order CT-DSM scheme, which can effectively utilize the oversampling and the noise shaping techniques to disperse the noise and push it to higher frequencies. Second, the use of the pseudo-inductor-current-sensor can increase the bandwidth of the closed-loop gain and consequently speeds up the transient response of the converter. Third, the dynamic-current regulator utilizes the principle of current charging and discharging to make the converter respond faster when the load changes dynamically. Fourth, this paper combines the pseudo-inductor-current-sensor and the dynamic-current regulator to realize the dual-current-acceleration technique, which can accelerate the transient response by up to 45.5%. The proposed converter is designed and fabricated in TSMC 0.18μm 1P6M CMOS process, and the chip area is 1.065 mm 2 . When the load current changes from 50mA to 500mA and 500mA to 50mA, the transient responses are 2.4μs and 3μs, respectively, and the peak efficiency is 92.4%. The measurement result of ONR is 78.087dB, with the sampling frequency of 10 MHz.