Hybrid pump-controlled asymmetric cylinder drive systems are implemented for energy-saving purposes in applications that do not require fast responses. Under low-velocity and low-pressure conditions, the friction influence in the hybrid pump-controlled system is evident. Researchers have developed various models to describe friction. These friction models are implemented based on the relative motion of the contact surfaces, and they can be categorised into static friction and dynamic friction models. For example, dynamic friction models are suitable for simulating the friction in hydraulic cylinder seals under lubrication conditions. Among the dynamic models, the LuGre model can capture almost all the static and dynamic friction behaviours at the macroscopic level, e.g., stiction, the Stribeck effect, and hysteresis. Thus, the LuGre model is suitable for describing the friction in hydraulic cylinders. As the friction force in the hydraulic cylinder is mainly from the cylinder seal, and the seal deformation occurs under pressure due to its flexibility, the friction in the hybrid pump-controlled hydraulic system is affected by the relative motion of the contact surfaces. Therefore, to investigate factors that affect the friction other than the relative motion of the contact surfaces, the friction behaviours of a hybrid pump-controlled hydraulic system are studied. A pressure difference and acceleration term are introduced in the LuGre friction model, and the simulated friction results of the updated LuGre model are compared with the measured experimental results to validate the new friction model.
The leaves of spinach are delicate and easily injured during harvesting. To reduce the spinach damage rate and increase the conveyance success rate, an orderly harvester was designed and manufactured, and the key conveying parameters of the harvester were optimized by simulation and experiments. The compression damage stress of spinach was determined by compression tests. Then, a finite element simulation model for spinach clamping was established, and the influence of different clamping heights on the spinach deformation and equivalent stress were simulated and analyzed. Finally, response surface Box–Behnken experiments were conducted to optimize the combinations of the twisting angle, clamping distance, and height difference. The results of the compression tests showed that the compression damage stresses of spinach leaves, stems, and their connection points were 8.04 × 10−2 MPa, 7.85 × 10−2 MPa, and 11.63 × 10−2 MPa, respectively. The optimal clamping height of spinach for orderly conveyance was obtained to be 20 mm according to the finite element simulation. The response surface experimental results indicated that the significance order of factors affecting the extrusion force was the clamping distance, the height difference, and the twisting angle. The significance order of factors affecting the conveyance success rate was the clamping distance, the twisting angle, and the height difference. The optimal parameter combination was ae twisting angle of 60°, clamping distance of 24 mm, and a height difference of 20 cm. The experimental validation of the optimization results from the finite element simulation and response surface tests demonstrated that the extrusion force and conveyance success rate were 2.37 N and 94%, respectively, with a conveying damage rate of 3% for spinach, meeting the requirements for the low-damage and orderly harvesting of spinach.
Hydroponic leafy vegetables have high yields, but their mechanized harvesting level is low. To improve the quality of orderly harvesting of hydroponic leafy vegetables, an ordered harvesting device with functions such as root flicking, posture adjustment and differential steering has been designed. A root-flicking method using rotating brushes was proposed, and experiments analyzed the effect of brush rotation direction. A posture adjustment method using a twisting conveyor belt was proposed, and experiments analyzed the impact of different twist angles on the stability of the adjustment process and the posture angle. A differential steering method using two pairs of conveyor belts with differential speeds was proposed, and experiments analyzed the impact of different steering belt speeds on steering stability and actual inclination angle. The root-flicking experiment results for hydroponic leafy vegetables showed that the counterclockwise followed by clockwise brush rotation combination performed better, with a root removal rate of 74.9%. The posture adjustment experiments on hydroponic leafy vegetables showed that the optimal twist angle for clamped and twisted conveyance was 35°, and the Mean Absolute Error (MAE) between the twist angle and hydroponic leafy vegetables posture angle was 0.38°. The differential steering experiment results indicated that the preferable belt speed difference for the directional conveyance of hydroponic leafy vegetables was 75 mm/s, and the MAE between the theoretical and actual inclination angles was 0.96°. Validation experiments based on posture adjustment and differential steering tests demonstrated a continuous harvesting success rate of 87.5%. This study provides valuable references for the design and development of orderly harvesting equipment for hydroponic leafy vegetables.