The technology of a pulsed detonation gun for gasification of organic waste with ultra-superheated steam has been experimentally demonstrated for the first time. Experiments were performed on natural gas conversion as well as on the gasification of liquid (waste machine oil) and solid (wood sawdust) waste by hot detonation products of natural gas–oxygen mixture at a frequency of detonation pulses f = 1 Hz. Periodic release of detonation products to a 100 L flow reactor provided a time-averaged mean temperature and pressure in the reactor at about 1200 K and 0.1 MPa. It is shown that the technology of a pulsed detonation gun can provide complete (100%) natural gas conversion to syngas containing H2 and CO with a H2/CO ratio of 1.25. During the gasification of liquid and solid wastes, the total volume fraction of combustible gases (H2, CO, and CH4) in the product syngas was 80 and 65% with H2/CO ratios of 0.8 and 0.5, respectively. Comparison of the experiments on natural gas conversion and liquid/solid organic waste gasification under the same conditions at f = 1 Hz showed that the composition of the product syngas in terms of H2 and CO content almost did not depend on the type of used feedstock. The estimated ideal energy gain defined as the ratio of the total energy of product syngas to the energy spent in its production from dry wood sawdust is about 4.6, i.e., the pulsed detonation technology of biomass gasification is economically very attractive.
A new type of marine transportation engine, the pulsed detonation hydroramjet (PDH), which was first designed, manufactured, and tested by the present authors, has been further investigated in terms of the potential improvement of its propulsive performance. PDH is composed of a pulsed detonation tube (DT) inserted in the flow-through water guide. Thrust is developed by shock-induced pulsed water jets which are periodically emitted from the water guide nozzle. The measured values of the time-averaged thrust and specific impulse in the first operation cycle were shown to always be considerably higher than those in subsequent cycles, indicating the possibility of improving the overall thrust performance. The present manuscript is aimed at clarifying the reasons for, and eliminating, cycle-to-cycle variability during PDH operation, as well as optimization of the PDH design. An experimental model of the PDH with an optically transparent water guide was designed and manufactured. The cycle-to-cycle variability was found to be caused by the overexpansion of gaseous detonation products in the DT due to the inertia of water column in the water guide. Gas overexpansion caused the reverse flow of the gas–water mixture which filled the water guide and penetrated the DT, thus exerting a strong effect on PDH operation. To eliminate the cycle-to-cycle variability, a new PDH model was developed, manufactured, and tested. The model was equipped with a passive flap valve and active rotary valve and operated on the stochiometric propane–oxygen mixture. Its test firing showed that use of the valves made it possible to eliminate the cycle-to-cycle variability and nearly double the time-averaged thrust and specific impulse reaching 40 N and 550 s, respectively.
The paper presents the results of experimental studies on the production of fine char powder from sunflower seed husks by a novel method of thermomechanical treatment with pulsed shock waves and supersonic jets of the mixture of ultra-superheated (above 2000 °C) steam and carbon dioxide, as well as the results of examination of the produced char powder in terms of its chemical, phase, and granulometric composition and structural, morphological, and texture characteristics. The objective of the research is to explore the possibility of using the resulting char powder as a sorption-active material for organic substances. It is shown that the obtained char particles and their agglomerates have an average size of 20–30 nm and 12–24 µm, respectively, have the shape of disks and ellipsoids, consist mainly of amorphous carbon (up to 56 wt%) and oxygen (up to 42 wt%), and have a specific surface area of 1.1–1.7 m2/g. It is concluded that such a char powder can be used as an absorbent for organic substances when dried and deagglomerated.
The pulsed detonation (PD) gun technology was applied for the autothermal high-temperature conversion of natural gas and atmospheric-pressure oxygen-free allothermal gasification of liquid/solid organic wastes by detonation-born ultra-superheated steam (USS) using two flow reactors of essentially different volume: 100 and 40 dm3. Liquid and solid wastes were waste machine oil and wood sawdust, with moisture ranging from 10 to 30%wt. It was expected that decrease in the reactor volume from 100 to 40 dm3, other conditions being equal, on the one hand, should not affect natural gas conversion but, on the other hand, could lead to an increase in the gasification temperature in the flow reactor and, correspondingly, to an increase in the product syngas (H2 + CO) quality. The PD gun was fed by natural gas–oxygen mixture and operated at a frequency of 1 Hz. As was expected, complete conversion of natural gas to product syngas in the PD gun was obtained with H2/CO and CO2/CO ratios equal to 1.25 and 0.25, irrespective of the reactor volume. Liquid and solid wastes were gasified to H2, CO, and CH4 in the flow reactors. The steady-state H2/CO and CO2/CO ratios in the syngas produced from waste machine oil were 0.8 and 0.5 for the 100-dm3 reactor and 0.9 and 0.2 for the 40-dm3 reactor, respectively, thus indicating the expected improvement in syngas quality. Moreover, the maximum mass flow rate of feedstock in the 40-dm3 reactor was increased by a factor of over 4 as compared to the 100-dm3 reactor. The steady-state H2/CO and CO2/CO ratios in the syngas produced from the fixed weight (2 kg) batch of wood sawdust were 0.5 and 0.8 for both reactors, and the gasification time in both reactors was about 5–7 min. The measured H2 vs. CO2 and CO vs. CO2 dependences for the syngas produced by the autothermal high-temperature conversion of natural gas and atmospheric-pressure allothermal gasification of liquid/solid organic wastes by USS at f = 1 Hz were shown to be almost independent of the feedstock and reactor volume due to high values of local instantaneous gasification temperature.