This paper examines the effect of oxygen concentration on the oxidation process and properties of aluminum particles, providing valuable insights for production and storage. Micron-grade aluminum powders were tested at heating rates of 5, 7.5, 10, and 15 K/min under oxygen concentrations of 7, 11, 15, 21, and 30 vol%. Results indicate a two-step mass gain oxidation process, with less pronounced mass gain at lower oxygen concentrations. SEM and XRD characterized the morphological and crystalline changes during oxidation. Lowering oxygen concentration from 30 vol% to 7 vol% increased the onset oxidation temperature by 17.1 °C. Increasing the proportion of inert gas in the atmosphere increases the ignition temperature of aluminum powder. The mathematical modeling approach of AKTS was used to decouple and analyze the thermal effects of simultaneous melting and oxidation, using the Friedman method to show that the apparent activation energy is about 350 kJ/mol in low-oxygen atmospheres (7 vol% and 11 vol%). The kinetics of aluminum oxidation were found to be closely related to the oxygen concentration, and based on the kinetics parameter, it is possible to predict a minimum limiting oxygen concentration.
25 September 2024 in Journal of Thermal Analysis and Calorimetry
Flame spread over discrete fuels is a typical phenomenon in fire scenes. Experimental and theoretical research on flame spread over discrete thermally thin fuels separated by air gaps with different inclination angles was conducted in the present study. Experiments with six inclination angles ranging from 0° to 85° and various fuel coverage rates from 0.421 to 1 were designed. The flame spread behavior, the characteristic flame size, and the flame spread rate were analyzed. The results show that the flow pattern, stability, and flame size exhibit different characteristics with different inclination angles and gap sizes. As the inclination angle increases, particularly with smaller gaps, turbulent and oscillating flames are observed, while larger gap sizes promote flame stability. The mechanism of flame propagation across the gap depends on the interplay between the flame jump effect and heat transfer, which evolves with gap size. Average flame height, average flame width, and flame spread rate initially increase and then decline with the increase in fuel coverage, peaking at fuel coverage rates between 0.93 and 0.571 for different inclination angles. A theoretical model is proposed to predict the flame spread rate and the variation in the flame spread rate with inclination angle and fuel coverage. Furthermore, the map determined by inclination angle and fuel coverage is partitioned into distinct regions, comprising the accelerated flame spread region, the flame spread weakening region, and the failed flame spread region. These findings provide valuable insights into flame spread dynamics over discrete thermally thin fuels under diverse conditions.
Aluminium powder, an energetic material, is prone to thermal runaway upon water exposure under local heat sources, yet the nonadiabatic mechanisms of micron sized accumulated aluminium powder under localized heating remain unclear. This study employs a proprietary characterization platform to investigate the effects of particle size, water content, and local heat source power on heat transfer in the dry state and on parameters including induction time, onset temperature, peak heat release rate, and reaction heat during the induction and main reaction phases. In the dry state, decreasing particle size enhances effective thermal conductivity and accelerates temperature rise, whereas elevated local heat source power exacerbates thermal inertia. Under local heating upon water exposure, reduced particle size significantly enhances reactivity; the reaction heat of 2 μm powder reaches 983 J/g, approximately fourfoldAs shown in Figure9 that of 106 μm powder. Water content exhibits nonmonotonic regulation, with onset temperature minimizing at 25% water content and 66.4 °C and reaction heat peaking at 33%. Paradoxically, elevated local heat source power suppresses reaction intensity, and reaction heat at 10 W is one sixth of that at 2.5 W, attributed to rapid product layer densification and the steam film barrier effect shifting the controlling mechanism from chemical to diffusion control. A coupled multifactorial predictive model incorporating the three factors was established with R2 of 0.92, providing data and guidance for aluminium powder storage hazard prevention.
Aluminium powder, an energetic material, is prone to thermal runaway upon water exposure under local heat sources, yet the nonadiabatic mechanisms of micron-sized accumulated aluminium powder under localised heating remain unclear. This study employs a proprietary characterisation platform to investigate the effects of particle size, water content, and local heat source power on heat transfer in the dry state and on parameters including induction time, onset temperature, peak heat release rate, and reaction heat during the induction and main reaction phases. In the dry state, decreasing particle size enhances effective thermal conductivity and accelerates temperature rise, whereas elevated local heat source power exacerbates thermal inertia. Under local heating upon water exposure, reduced particle size significantly enhances reactivity; the reaction heat of 2 μm powder reaches 983 J/g, approximately fourfold that of 106 μm powder. Water content exhibits a nonmonotonic effect, with the onset temperature reaching a minimum of 66.4 °C at a water content of 25%, while the reaction heat peaks at 33% water content. Interestingly, increasing local heat source power was found to suppress reaction intensity, and reaction heat at 10 W is one sixth of that at 2.5 W, attributed to rapid product layer densification and the possible steam-film barrier effect shifting the controlling mechanism from chemical to diffusion control. A coupled multifactorial predictive model incorporating the three factors was established with a correlation coefficient R2 of 0.92, providing a theoretical basis and practical guidance for hazard assessment and safe storage of aluminium powder.