Mohammad Arafat

Mr. Mohammad Arafat

orcid

Research Focus & Metrics

Academic Career Length

8Years (2019-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
5 June 2020 in SN Applied Sciences
Verified
Journal Article
Closed access
PDF file
MAMohammad Arafat
Mohammad Arafat
TSTeddy Sjafrizal
Teddy Sjafrizal
RARino Andias Anugraha
Rino Andias Anugraha

1 April 2022 in CFD Letters
Verified
Journal Article
Open access
PDF file
MAMohammad Arafat
Mohammad Arafat
IIIzuan Amin Ishak
Izuan Amin Ishak
The development of Next-Generation Trains (NGT) made of lightweight materials is a challenging task for the transport industry. It reduces axle loads, which saves money by lowering rail track maintenance costs and the amount of energy needed to drive vehicles. However, the increasing speed and decreasing mass of high-speed trains, on the other hand, raises concerns about the effects of strong crosswinds on their aerodynamics and train stability. As a result, the purpose of this research is to investigate the unsteady flow structure around an NGT in crosswind using a Computational Fluid Dynamics (CFD) technique known as Unsteady Reynolds Averaged Navier-Stokes (URANS). Based on the height of the train model and the velocity, the Reynolds number for the simulation used was . The simulation run in four different crosswind angles: 5°, 10°, 15°, and 20°. The simulation results were compared with experimental results. The findings revealed that a larger yaw angle, which is primarily determined by the incoming wind velocity, can lead to higher flow separation and a more complex three-dimensional flow around the train. Additionally, when the wind angle is small, separation of flow and wakes is limited to the train's end; however, as the wind angle increases, separation of flow occurs from the train's upper and lower corners, indicating that the vortices formed as a result of the flow passing over the roof top and underbody. Finally, the study's findings will contribute to a better understanding of the flow characteristics around an NGT in crosswinds, which is simply impossible to achieve through full-scale testing due to the cost, resources, and accuracy.

15 September 2024 in JOURNAL OF ADVANCED RESEARCH IN EXPERIMENTAL FLUID MECHANICS AND HEAT TRANSFER
Verified
Journal Article
Open access
PDF file
MAMohammad Arafat
Mohammad Arafat
IIIzuan Amin Ishak
Izuan Amin Ishak
MAMuhammad Aidil Safwan Abdul Aziz
Muhammad Aidil Safwan Abdul Aziz
ASAndrew Wee Shong Soh
Andrew Wee Shong Soh
WTWoei Ting Tiong
Woei Ting Tiong
RRRazlin Abd Rashid
Razlin Abd Rashid
Electric city vehicles are vital for reducing pollution in urban areas due to their zero emissions and high energy efficiency, significantly improving air quality and reducing the carbon footprint. This study investigates the aerodynamic behavior of simplified city vehicle models using computational fluid dynamics (CFD) simulations based on Reynolds-Averaged Navier-Stokes (RANS) and Detached Eddy Simulation (DES) turbulence model. The models are tested at speeds of 10 m/s, 15 m/s, and 20 m/s, with a grid independence study to ensure reliable results. ANSYS Fluent is used for the simulations, comparing the results from RANS and hybrid RANS/LES or DDES in terms of aerodynamic forces and flow patterns around the vehicle. Results show that the drag coefficient (Cd) decreases with increasing speed for both RANS and DDES models. At 10 m/s, the drag coefficients are 0.541 for RANS and 0.524 for DDES, a 3.14% reduction. At 15 m/s, the drag coefficients are 0.539 for RANS and 0.518 for DDES, a 3.89% reduction. At 20 m/s, the drag coefficients are 0.538 for RANS and 0.514 for DDES, a 4.46% reduction. Flow visualizations show that DDES simulations capture more detailed and complex flow structures, particularly in the wake region, compared to the smoother RANS patterns. These findings are essential guidelines for optimizing vehicle design to enhance aerodynamic performance and contribute to the development of more efficient, environmentally friendly urban transportation solutions.

1 January 2019 in Journal of Physics: Conference Series
Verified
Conference Paper
Open access
PDF file
ILI Lestari
I Lestari
MAMohammad Arafat
Mohammad Arafat
Offshore wind turbine is being the trend because the consistency wind resource on open seas. But the harsh environmental condition could lead to damage, corrosion, and erosion. With these challenges, structural health monitoring (SHM) plays an important role to ensure the functionality of offshore turbines, and wireless sensor networks (WSNs) help to reduce costs compared to the wire-based ones. This paper presents a literature review for two of main parameters to deploy WSNs for SHM; data rate and bandwidth which indicate the efficiency of communication for each nodes.

30 November 2024 in Journal of Advanced Research in Numerical Heat Transfer
Verified
Journal Article
Open access
PDF file
MAMuhammad Aidil Safwan Abdul Aziz
Muhammad Aidil Safwan Abdul Aziz
NDNofrizalidris Darlis
Nofrizalidris Darlis
IIIzuan Amin Ishak
Izuan Amin Ishak
NZNor Atiqah Zolpakar
Nor Atiqah Zolpakar
MAMohammad Arafat
Mohammad Arafat
MMMuhammadu Masin Muhammadu
Muhammadu Masin Muhammadu
The increasing miniaturization of technology has intensified thermal challenges, particularly concerning the cooling of small components like ICs and CPUs. Microchannel heat sinks offer a common solution, but optimizing their configurations remains a subject of interest. This study addresses multiple thermal enhancing factors that is position of the inlet and outlet and integrating pin-fin configurations. The objectives of the study are to improve the thermal uniformity of the heat sink and to analyse the thermal performance across the different geometry of pin-fin using Ansys. The thermal performance parameters focused on this study are the maximum temperature and pressure drop. The results gathered that hexagon shaped pin fin yield better thermal performance as compared to the other geometry as it shows the lowest maximum temperature, lowest thermal resistance and lowest pressure drop. This proves the significance of geometry selection for the pin fin as it affected the thermal performance of the microchannel heat sink with cross flow effects.

1 December 2024 in Engineering Research Express
Verified
Journal Article
Closed access
MAMohammad Arafat
Mohammad Arafat
IIIzuan Amin Ishak
Izuan Amin Ishak
NMNurshafinaz Mohd Maruai
Nurshafinaz Mohd Maruai
This study explores the complexities of UAV propeller aerodynamics by examining the influence of various parameters, including mesh resolutions, timestep sizes, iterations per timestep, and different Reynolds-Averaged Navier–Stokes (RANS) turbulence models, using Delayed Detached Eddy Simulation (DDES). Through extensive computational fluid dynamics (CFD) simulations, the aerodynamic performance of the propeller is analyzed under different conditions. Mesh resolutions from coarse to fine are evaluated, with Grid Convergence Index (GCI) and Richardson Extrapolation applied to ensure mesh-independent results. Timestep sizes ranging from 0.5° to 10° are also analyzed, revealing a trade-off between accuracy and computational efficiency. Furthermore, the study assesses the impact of different numbers of iterations per timestep and compares three distinct RANS turbulence models: k-ω SST, Spalart-Allmaras, and Realizable k-ε. The results show that finer mesh resolutions and smaller timesteps enhance accuracy in thrust and torque predictions. The k-ω SST model demonstrates the best balance between thrust generation and torque minimization, while the Spalart-Allmaras model underperforms in both categories. In addition, fewer iterations per timestep were found to be sufficient for convergence, reducing computational cost. Overall, this study provides a comprehensive evaluation of UAV propeller performance using CFD simulations.