Recently, high-entropy alloys (HEAs) have attracted much attention because of their superior properties, such as high strength and corrosion resistance. This study aimed to investigate the influences of process parameters on the microstructure and mechanical properties of CoCrFe NiTiMo HEAs using a laser-based powder bed fusion (LPBF) process. In terms of laser power and scan speed, a process map was constructed by evaluating the density and surface roughness of the as-built specimen to optimize the process parameters of the products. The mechanical properties of the as-built specimens fabricated at the optimum fabrication condition derived from the process map were evaluated. Consequently, the optimum laser power and scan speed could be obtained using the process map evaluated by density and surface roughness. The as-built specimen fabricated at the optimum fabrication condition presented a relative density of more than 99.8%. The microstructure of the as-built specimen exhibited anisotropy along the build direction. The tensile strength and elongation of the as-built specimen were around 1150 MPa and more than 20%, respectively.
A series of Mg–Ni or Mg–Cu alloys with Mg content comprised between 55 and 77 at% Mg was prepared by mechanical alloying with the aim of synthesizing Mg2Ni and Mg2Cu phases, respectively. Their morphology and structural properties were characterized by scanning electron microscopy (SEM) and X-ray Diffraction (XRD). High Pressure Differential Scanning Calorimetry (HP-DSC) was used to evaluate their hydrogenation properties. For the Mg–Ni series, 8 hours of milling were enough to synthesize the Mg2Ni alloy. The highest reversible hydrogen capacity (2.8 mass%) was obtained for 70 at% Mg sample without the need of any activation treatment. For Mg–Cu series, 83 mass% of Mg2Cu was obtained after 4 hours of milling. From the view point of alloying composition, Mg-rich samples show better crystallinity of Mg2Cu phase. Under hydrogen, the Mg2Cu powder mixtures decompose and form MgH2 hydride storing 1.56 mass% of hydrogen for 66 at% Mg. For the Mg–Ni series, Cu or Al elements (1 to 10 mass%) were added during milling. HP-DSC runs show that they destabilize the hydride phase due to alloying effects.
This study aims to clarify the influence of the Spark Plasma Sintering (SPS) method on structural morphology, mechanical properties and also functional characteristics, such as hydrogen absorbing properties, for titanium-iron intermetallic compounds. We could synthesize B2-TiFe phase using mechanical alloying (MA) during 3 h and SPS treatment of 5 min at 500–1000 °C, which was confirmed by XRD and Electron Probe Microanalyzer (EPMA) measurements. In addition, the synthesized TiFe intermetallic compound has been found to absorb hydrogen with high kinetics in both high pressure Differential Scanning Calorimetry (DSC) and Pressure-Composition-Temperature (PCT) measurements. Therefore, we have successfully developed TiFe alloy in bulk form from initial raw powders by using a combination of short period mechanical alloying and SPS heat treatment. This combined route enhances the potential of the SPS method to synthesize new materials.
1 November 2016 in International Journal of Metalcasting
It is well known that the mechanical properties of spheroidal graphite cast iron deeply depend on the volume of pearlite matrix microstructures. Therefore, the theoretical criterion of pearlite matrix nucleation is considered important in this graphite cast iron that to obtain the higher mechanical properties of graphite cast iron, the pearlite stabilizing element such as Mn or Cu is very important. The present work aims to study the influence of manganese (Mn) content and heat treatment on the mechanical properties of 3% or 4% (Solution Strengthened Ferritic Ductile Iron-SSFDI) of silicon (Si) containing spheroidal graphite cast irons. The six 3.6%C–3%Si melts with different chemical compositions from 0.2 to 1.7 mass% of Mn content were produced using a high-frequency induction furnace. The melt was poured into a Y-block CO2 sand mold of 25 or 40 mm in thickness. The microstructure analysis and mechanical testing were performed for as-cast and some heat treatment conditions, such as annealing or air cooling. As a result, the tensile strength had a good relationship with the area fraction of pearlite, over 600 MPa in UTS, and high proof stress for some 3 or 4%Si–Mn series samples in the as-cast condition. By the heat treatment from the unique (α + γ) region, the 3% Si sample showed over 800 MPa and over 10% in elongation. And 4%Si–1.5%Mn (SSFDI) series sample showed over 600 MPa in UTS and over 15% in elongation which was prepared by annealing heat treatment to reduce to less than 5% of the area fraction of pearlite. This study suggests that it can be understood of the correlation between optimizing the heat treatment condition and mechanical properties of SSFDI cast irons.
Accuracy Improving Methods in Estimation of Graphite Nodularity of Ductile Cast Iron by Measurement of Ultrasonic Velocity | InTechOpen, Published on: 2012-09-26. Authors: Minoru Hatate, Tohru Nobuki and Shinichiro Komatsu