At the Japan Proton Accelerator Research Complex (J-PARC), a pulsed spallation neutron source provides neutrons with high intensity and narrow pulse width pulse to promote researches on a variety of science in the Materials and Life Science Experimental Facility (MLF). It was designed to be driven by a proton beam with an energy of 3 GeV, a power of 1 MW at a repetition rate of 25 Hz, that is world’s highest power level. It is still on the way towards the goal to accomplish the operation with a 1 MW proton beam. In this review, distinctive features of the target-moderator-reflector system of the pulsed spallation neutron source are presented.

A MW-class mercury target for the spallation neutron source is subjected to the pressure waves and cavitation erosion induced by high-intense pulsed-proton beam bombardment. Helium-gas microbubbles injection into mercury is one of the effective techniques to suppress the pressure waves. The microbubble injection technique was developed. The selection test of bubble generators indicated that the bubble generator utilizing swirl flow of liquid (swirl-type bubble-generator) will be suitable from the viewpoint of the produced bubble size. However, when single swirl-type bubble-generator was used in flowing mercury, swirl flow of mercury remains at downstream of the generator. The remaining swirl flow causes the coalescence of bubbles which results in ineffective suppression of pressure waves. To solve this concern, a multi-swirl type bubble-generator, which consists of several single swirl-type bubble-generators arraying in the plane perpendicular to mercury flow direction, was invented. The multi-swirl type bubble-generator was tested in mercury and the geometry was optimized to generate small bubble with low flow resistance based on the test results. It is estimated to generate the microbubbles of 65 μm in radius under the operational condition of the Japanese Spallation Neutron Source mercury target, which is the sufficient size to suppress the pressure waves.

To perform basic Research and Development for future Accelerator-driven Systems (ADSs), Japan Proton Accelerator Research Complex (J-PARC) will construct an ADS target test facility. A Lead–Bismuth Eutectic (LBE) spallation target will be installed in the target test facility and bombarded by pulsed proton beams (250 kW, 400 MeV, 25 Hz, and 0.5 ms pulse duration). To realize the LBE spallation target, cavitation damage due to pressure changes in the liquid metal should be determined, preliminarily, because such damage is considered to be very critical, from the viewpoint of target safety and lifetime. In this study, cavitation damage due to pressure waves caused by pulsed proton beam injection and turbulent liquid metal flow, were studied, numerically, from the viewpoint of single cavitation bubble dynamics. Specifically, the threshold of cavitation and effects of flow speed fluctuation on cavitation bubble dynamics, in an orifice structure, were investigated in the present work. The results showed that the LBE spallation target did not undergo cavitation damage, under normal nominal operation conditions, mainly because of the long pulse duration of the pulsed proton beam and the low liquid metal flow velocity. Nevertheless, the possibility of cavitation damage in the orifice structure, under certain extreme transient LBE flow conditions, cannot be neglected.

Neutron flux per pulse reached world record at neutron source in Japan Proton Accelerator Research Complex (J-PARC). In the J-PARC, mercury target system is used as a spallation neutron source. A target vessel has a multi-walled protection system that comprises a mercury vessel enclosed with a double-walled water shroud. This is to prevent the leakage of the mercury outside the target vessel. The multi-walled structure needed to be complicated with a lot of welding lines. However, during the operation, we faced an unscheduled shutdown due to water leakage to the intermediate layer between the mercury vessel and water shroud. An investigation on the cause of the leakage was carried out. It is deduced that the leakage path was formed due to the crack propagation from welding defects that are caused by the complicated multi-walled structure. The crack propagation is attributed to the repeated stress by pressure waves generated in the mercury target. Based on the investigation results, the design was improved to remove the welding line on the complicated structure and to realize the stable operation with 1 MW proton beam, which is the final design value of the neutron source in J-PARC.

Microbubbles have been applied in various fields. In the mercury targets of spallation neutron sources, where cavitation damage is a crucial issue for life estimation, microbubbles are injected into the mercury to absorb the thermal expansion of the mercury caused by the pulsed proton beam injection and reduce the macroscopic pressure waves, which results in reducing the damage. Recently, when the proton beam power was increased and the number of injected gas bubbles was increased, unique damage morphologies were observed on the solid–liquid interface. Detailed observation and numerical analyses revealed that the microscopic pressure emitted from the gas bubbles contracting is sufficient to form pit damage, i.e., the directions of streak-like defects which are formed by connecting the pit damage coincides with the direction of the gas bubble trajectories, and the distances between the pits was understandable when taking the natural period of gas bubble vibration into account. This indicates that gas microbubbles, used to reduce macroscopic pressure waves, have the potential to be inceptions of cavitation damage due to the microscopic pressure emitted from these gas bubbles. To completely mitigate the damage, we have to consider the two effects of injecting gas bubbles: reducing macroscopic pressure waves and reducing the microscopic pressure due to bubble dynamics.