A moment magnitude 5.4 earthquake struck the Pohang city located in the southeastern Korean Peninsula on 15 November 2017, possibly triggered by an enhanced geothermal system. Despite the moderate magnitude of the earthquake, extensive geotechnical and structural damage occurred. This study summarizes the widespread geotechnical damage resulted from the Pohang earthquake, observed during our reconnaissance trip. The affected area is mainly covered by Tertiary/Quaternary Alluvium underlain by mudstones with a thickness of approximately 500 m. Because of the soft grounds and shallow focal depth, this area experienced ground settlements up to 39 cm, building settlements that made apartments tilted by 1.6°. We also present observations on ground cracks, lateral spreadings, landslides, retaining wall deformations, and liquefactions. Documenting the damage is significant because (1) those are the first earthquake‐induced damage observed in Korea, and (2) those are caused by the shallow‐depth earthquake possibly induced by an enhanced geothermal system.
Three-dimensional (3D) curved wall jets are a significant topic in various applications related to local heat and mass transfer. This study investigates the effects of the impinging angle and Reynolds number with a fixed distance from the nozzle to the surface of a cylinder. The particle image velocimetry (PIV) method was used to measure the mean streamwise velocity profiles, which were normalized by the maximum velocity along the centerline of the impinging jet onto the cylinder. After the impingement of the circular jet, a 3D curved wall jet develops on the cylinder surface due to the Coanda effect. At a given Reynolds number, the initial momentum of the wall jet increases, and flow separation occurs further downstream than in normal impingement as the impinging angle increases. At a given impinging angle, flow separation is delayed with increasing Reynolds number. A self-preserving wall jet profile was not attained in the 3D curved wall jet. The turbulence intensity and the Reynolds shear stress were obtained to analyze the turbulence characteristics. The radial turbulence intensity showed similar tendencies to a two-dimensional (2D) curved wall jet, but the streamwise turbulence intensity was dissimilar. The Reynolds shear stress decreases downstream of the cylinder wall due to the decreased velocity and centrifugal force.
This paper presents a novel analytical solution for journal-bearing viscoelastic lubrication using the perturbation method. The nonlinear Giesekus model was used for the constitutive equations to study the effects of fluid elasticity, shear-thinning viscometric functions, and strain-hardening elongational viscosity of viscoelastic lubrication. The investigation focuses on the impact of characteristic parameters such as mobility factor, eccentricity ratio, and Weissenberg number on the fluid film pressure distribution, load capacity, and shear stress. Although distinguishing between the normal stress differences and extensional viscosity in mixed viscoelastic flows is complicated, we investigated the role and contribution of these two factors. By increasing the elasticity of the fluid, the portion of both mentioned parameters increases consequently. Furthermore, analyses and comparisons show the contributions of the first normal stress and elongational viscosity to the load capacity of the bearing through the stress ratio and flow type parameter for the first time. The research findings indicate that fluid elasticity enhances the load capacity of the bearing compared to a Newtonian lubricant with the same effective viscosity. Moreover, the bearing load capacity is divided into two regions. In the linear region, the mobility factor and Weissenberg numbers have minimal effects leading to a linear increase in the load distribution, and in the exponential region, the load capacity changes are considerable. This research provides valuable insights into the behavior of viscoelastic lubrication in journal-bearing systems.
A kHz phosphor thermometry technique was developed for contactless two-dimensional measurements with Mg4FGeO6: Mn4+ utilizing its rise and decay of the phosphorescence. Different from the traditional method that phosphorescence rises when the decay is complete, high-frequency excitation light was applied in this study, which causes a rise of phosphorescence with an incomplete decay of phosphorescence. This eventually causes the phosphor to emit a waveform signal. Experimental results show that this phosphorescence waveform signal is stable and only affected by temperature when the excitation conditions are fixed. A calibration curve can then be obtained by calculating the ratio of the crests and troughs of the phosphorescence signal. This study shows that the developed method has high precision and is easy to operate for two-dimensional high-frequency temperature measurement.
This study investigates the effect of fluid elasticity on axisymmetric droplets colliding with pre-existing liquid films, using both numerical and experimental approaches. The numerical simulations involve solving the incompressible flow momentum equations with viscoelastic constitutive laws using the finite volume method and the volume of fluid (VOF) technique to track the liquid’s free surface. Here, the Oldroyd-B model is used as the constitutive equation for the viscoelastic phase. Experiments are also performed for dilute viscoelastic solutions with 0.005% and 0.01% (w/w) polyacrylamide in 80:20 glycerin/water solutions, in order to ensure the validity of the numerical solution and to investigate the elasticity effect. The formation and temporal evolution of the crown parameters are quantified by considering the flow parameters, including the fluid’s elasticity. The results indicate that the axisymmetric numerical solutions reasonably agree with the experimental observations. Generally, the fluid’s elasticity can enlarge the crown dimension at different thicknesses of the fluid film. Moreover, at intermediate values of the Weissenberg number, the extensional force in the crown wall can control the crown propagation. Furthermore, the results reveal that the effects of the Weber number and the viscosity ratio on this problem are more significant at higher values of the Weissenberg number.
This study examined the impact of Boger droplets on spherical surfaces, considering the various properties of liquids and surfaces for the first time. The experimental setup involved spheres with three different diameters composed of hydrophilic and hydrophobic surfaces. The main innovative aspect of the present study lies in the examination of the effects of rheological properties including elasticity, elongational viscosity, and the first normal stress difference on the impact of Boger droplets on solid surfaces via stress analysis. For this purpose, the results of the impact of Boger droplets are compared to the impact of equivalent Newtonian droplets with the same viscosity and surface tension coefficient. The research also explored the influences of Weber number, diameter ratio, and surface wettability on the dynamic behaviors of viscoelastic droplets during the spreading and receding stages. The results suggested that increasing the Weber number increases the maximum spreading factor of the droplets. A smaller diameter ratio required more time to reach this factor. The surface wettability significantly affected the receding phase, while its effect on the spreading stage was minimal. Droplets exhibited more retraction on surfaces with higher contact angles. The Newtonian fluids showed greater spreading and retraction than viscoelastic fluids with the same viscosity, highlighting the influence of fluid elasticity. It is shown that the normal stress caused by extensional viscosity during droplet spreading is significantly higher than the normal stress difference resulting from shear deformation, showing different behaviors between these two types of stress concerning droplets.