In the fabrication of soft magnetic composites, the lattice mismatch between the inorganic insulation layer and the iron matrix often leads to the formation of cracks during the molding process, which significantly impairs the operational performance of the materials. Consequently, it is imperative to develop novel strategies for inorganic insulation coatings that offer high electrical resistivity and thermal stability and are less susceptible to cracking during formation. This paper presents a new structure for soft magnetic composites that incorporates FePO4 as an intermediate transition layer between the iron-based soft magnetic particles and the inorganic ceramic insulation layer. This configuration is designed to provide insulation coatings with superior voltage and thermal resistance, as well as high electrical resistivity. The research details the processes forming the FePO4 intermediate transition layer and the SiO2 insulation layer on the iron powder surface, along with their interaction mechanisms. An analysis comparing the scenarios with and without the FePO4 intermediate transition layer shows its beneficial impact on the magnetic properties and mechanical strength of the soft magnetic composites. Further investigations reveal that at a phosphoric acid concentration of 1 wt.%, the FePO4 layer significantly enhances the interface compatibility between the Fe powder matrix and the SiO2 insulation layer. Under these conditions, the Fe@ FePO4/SiO2 soft magnetic composites demonstrate outstanding overall performance: the saturation magnetization stands at 215.60 emu/g, effective permeability at 83.2, resistivity at 57.42 Ω·m, power loss at 375.0 kW/m3 under 30 mT/100 kHz, and radial compressive strength at 15.95 Kgf. These findings offer novel insights and practical approaches for advancing inorganic insulation coating strategies and provide vital scientific support for further enhancing the magnetic and mechanical properties of soft magnetic composites.
19 February 2020 in Metallurgical Research & Technology
From the results calculated by theoretical derivations, it was found that the characteristics of tuyere raceway determined by the operation condition for blast air played a critical effect on the heart activity. The speed and kinetic energy of blast air should be proportional to the volume of blast furnace (BF), and the comprehensive optimization of air volume and tuyere which should vary with the quality of raw materials was essential. The calculation methods of air volume ratio and coefficient for different BFs were put forward. Moreover, the details on hearth activity recovery of a 4747 m3 blast furnace in China were elaborated. Based on the extensive experience in blast furnace production, the various phenomena used to judge air speed and kinetic energy whether reasonable were discussed. In summary, hearth activity was closely related to the characteristics of BF raceway and reasonable air speed and kinetic energy could effectively improve the activity.
25 October 2023 in Metallurgical Research & Technology
Based on the fundamental processes and principles of ironmaking in a BF, an analysis was conducted on the production technical data from 18 large-scale 3200 m3 BFs in China in 2020. The study systematically investigated the influence of top pressure on reduction, air injection, furnace top, energy consumption, and pig iron composition within the BF. Practical operations in a newly No. 1 3200 m3 BF in a Chinese company demonstrated that increasing the top pressure not only effectively improved the smelting process, operational stability, and reduced furnace fluctuations but also led to a decrease in dust emissions, increased pig iron yield and quality, and significantly reduced fuel consumption and process energy consumption. Against the backdrop of dual carbon objectives, gaining a scientific understanding of the dynamic operation principles of the BF smelting process and continuously exploring low-carbon ironmaking methods have become the focus for professionals and researchers in the fields of BF ironmaking, production management, technology, and scientific research.
27 January 2020 in Metallurgical Research & Technology
This article has reviewed the production status, total reductant consumption, raw materials and operation principle indexes of large blast furnaces in China from 2015 to 2016. The developing actuality of Chinese large BFs has been quantitatively analyzed and the existing problems have been proposed clearly. Based on that, maintaining production stable, enhancing the quality of raw materials and improving the operation principles are suggested. Large BFs take advantages of high-quality hot metal, energy saving, cost-cutting, high mechanization and automation levels and are sufficient to meet the challenges of economic crisis, environmental pressure and security risk form the future. Thus, the number of large BFs in China will continue to increase in the future.
Hydrogen removal of H-supersaturated liquid steel produced in a hydrogen-rich environment in an industrial vacuum degasser (VD) is simulated here using a two-phase (argon–steel) Eulerian model. The dehydrogenation efficiency is evaluated for a series of ladle plug layouts and argon-purging modes. Increasing the plug number from the prototype double-plug of the ladle to four or slightly prolonging the degassing time of a triple-plug ladle enables to obtain the specified dehydrogenation efficiency and the end-point hydrogen level. Varying the plug position of the triple-plug ladle makes no significant difference in the dehydrogenation efficiency, which, however, is improved by adjusting the plug angle. For the triple-plug ladle, the non-uniform argon-purging mode improves the melt hydrodynamic conditions, but the optimal dehydrogenation performance is achieved in the uniform mode. The plug number has the greatest impact on the dehydrogenation efficiency compared to the other ladle designs considered. The high-efficiency dehydrogenation of H-supersaturated liquid steel in the VD can be achieved through using the quadruple plugs, or by using the triple plugs positioned at 0.57R, 0.57R, and 0.41R and the angles of 108.6° and 71.4°, with the uniform argon-purging flow rate.
13 May 2020 in Metallurgical Research & Technology