Millimeter wave (MmWave) communications is capable of supporting multi-gigabit wireless access thanks to its abundant spectrum resource. However, severe path loss and high directivity make it vulnerable to blockage events, which can be frequent in indoor and dense urban environments. To address this issue, in this paper, we introduce intelligent reflecting surface (IRS) as a new technology to provide effective reflected paths to enhance the coverage of mmWave signals. In this framework, we study joint active and passive precoding design for IRS-assisted mmWave systems, where multiple IRSs are deployed to assist the data transmission from a base station (BS) to a single-antenna receiver. Our objective is to maximize the received signal power by jointly optimizing the transmit precoding vector at the BS and the phase shift parameters used by IRSs for passive beamforming. Although such an optimization problem is generally non-convex, we show that, by exploiting some important characteristics of mmWave channels, an optimal closed- orm solution can be derived for the single IRS case and a near-optimal analytical solution can be obtained for the multi-IRS case. Our analysis reveals that the received signal power increases quadratically with the number of reflecting elements for both the single IRS and multi-IRS cases. Simulation results are included to verify the optimality and near-optimality of our proposed solutions. Results also show that IRSs can help create effective virtual LOS paths and thus substantially improve robustness against blockages in mmWave communications.

Reconfigurable intelligent surface (RIS) is envisioned to be an essential component of the paradigm for beyond 5G networks as it can potentially provide similar or higher array gains with much lower hardware cost and energy consumption compared with the massive multiple-input multiple-output (MIMO) technology. In this paper, we focus on one of the fundamental challenges, namely the channel acquisition, in a RIS-assisted multiuser MIMO system. The state-of-the-art channel acquisition approach in such a system with fully passive RIS elements estimates the cascaded transmitter-to-RIS and RIS-to-receiver channels by adopting excessively long training sequences. To estimate the cascaded channels with an affordable training overhead, we formulate the channel estimation problem in the RIS-assisted multiuser MIMO system as a matrix-calibration based matrix factorization task. By exploiting the information on the slow-varying channel components and the hidden channel sparsity, we propose a novel message-passing based algorithm to factorize the cascaded channels. Furthermore, we present an analytical framework to characterize the theoretical performance bound of the proposed estimator in the large-system limit. Finally, we conduct simulations to verify the high accuracy and efficiency of the proposed algorithm.

This paper investigates a novel unmanned aerial vehicles (UAVs) secure communication system with the assistance of reconfigurable intelligent surfaces (RISs), where a UAV and a ground user communicate with each other, while an eavesdropper tends to wiretap their information. Due to the limited capacity of UAVs, an RIS is applied to further improve the quality of the secure communication. The time division multiple access (TDMA) protocol is applied for the communications between the UAV and the ground user, namely, the downlink (DL) and the uplink (UL) communications. In particular, the channel state information (CSI) of the eavesdropping channels is assumed to be imperfect. We aim to maximize the average worst-case secrecy rate by the robust joint design of the UAV’s trajectory, RIS’s passive beamforming, and transmit power of the legitimate transmitters. However, it is challenging to solve the joint UL/DL optimization problem due to its non-convexity. Therefore, we develop an efficient algorithm based on the alternating optimization (AO) technique. Specifically, the formulated problem is divided into three sub-problems, and the successive convex approximation (SCA), $\mathcal {S}$ -Procedure, and semidefinite relaxation (SDR) are applied to tackle these non-convex sub-problems. Numerical results demonstrate that the proposed algorithm can considerably improve the average secrecy rate compared with the benchmark algorithms, and also confirm the robustness of the proposed algorithm.

This paper investigates the passive beamforming and information transfer (PBIT) technique for multiuser multipleinput multiple-output (Mu-MIMO) systems with the aid of reconfigurable intelligent surfaces (RISs), where the RISs enhance the primary communication via passive beamforming (P-BF) and at the same time deliver additional information by the on-off reflecting modulation (in which the RIS information is carried by the on/off state of each reflecting element). For the P-BF design, we propose to maximize the achievable user sum rate of the RIS-aided Mu-MIMO channel and formulate the problem as a two-step stochastic program. A sample average approximation (SAA) based iterative algorithm is developed for the efficient PBF design of the considered scheme. To strike a balance between complexity and performance, we further propose a simplified P-BF algorithm by approximating the stochastic program as a deterministic alternating optimization problem. For the receiver design, the signal detection at the receiver is a bilinear estimation problem since the RIS information is multiplicatively modulated onto the reflected signals of the reflecting elements. To solve this bilinear estimation problem, we develop a turbo message passing (TMP) algorithm in which the factor graph associated with the problem is divided into two modules: one for the estimation of the user signals and the other for the estimation of the on-off state of each RIS element. The two modules are executed iteratively to yield a near-optimal low-complexity solution. Furthermore, we extend the design of the Mu-MIMO PBIT scheme from single- RIS to multi-RIS, by leveraging the similarity between the single- RIS andmulti-RIS system models. Extensive simulation results are provided to demonstrate the advantages of our P-BF and receiver designs.