Rogelio Martínez Oropeza

Dr. Rogelio Martínez Oropeza

orcid

Research Focus & Metrics

Academic Career Length

3Years (2024-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
20 October 2024 in Processes
Verified
Journal Article
Open access
PDF file
SGSANDRO GUADALUPE PEREZ GRAJALES
SANDRO GUADALUPE PEREZ GRAJALES
TOTeresa Hernández Ortíz
Teresa Hernández Ortíz
RORogelio Martínez Oropeza
Rogelio Martínez Oropeza
TTTabai Torres-Díaz
Tabai Torres-Díaz
LLLuis Adrián López-Pérez
Luis Adrián López-Pérez
DRDavid Juárez Romero
David Juárez Romero
Solar energy is one of the main renewable energy resources due to its abundance. It can be used for two purposes, thermal or photovoltaic applications. However, when the resource obtained is mixed, it is called photovoltaic thermal hybrid, where the solar panels generate electricity and are provided with a heat exchanger to absorb energy through a water flow. This is one of the techniques used by the scientific community to reduce the excess temperature generated by solar radiation in the cells, improving the electrical efficiency of photovoltaic systems and obtaining fluid with higher temperature. In this work, the thermal behavior of a heat exchanger equipped with fins in its interior to increase the thermal efficiency of the system was analyzed using CFD (Computational Fluid Dynamics). The results showed that the average fluid outlet temperature was 75.31 °C, considering an incident irradiance of 1067 W/m2 and a fluid inlet temperature of 27 °C. The operating conditions were obtained from published experimental studies, achieving 97.7% similarity between the two. This was due to the boundary conditions of the heat flux (1067 W/m2) impinging directly on the coupled cells and the heat exchanger in a working area of 0.22 m2.

5 May 2025 in International Journal of Renewable Energy Development
Verified
Journal Article
Open access
PDF file
RORogelio Martínez Oropeza
Rogelio Martínez Oropeza
JGJuan Carlos Garcia
Juan Carlos Garcia
LCLaura Castro
Laura Castro
IVItzel Vera-Wilimek
Itzel Vera-Wilimek
Oscar Alfredo Jaramillo-SalgadoOscar Alfredo Jaramillo-Salgado
Oscar Alfredo Jaramillo-Salgado
JRJosé Omar Dávalos Ramírez
José Omar Dávalos Ramírez
To spread the use of Wind H-Darrieus turbines to electricity generation in urban or rural environments is necessary to improve some of its main drawbacks such as: aerodynamic efficiency, self-starting capability and torque fluctuations. The aims of this study are to enhance the aerodynamic efficiency and self-starting capability of an H-Darrieus turbine through wind tunnel tests combined using a 3D numerical study using Computational Fluid Dynamics (CFD). The NREL S815 profile and four modified versions were evaluated, including one with a 19.2% increase in thickness and three chord-to-diameter ratios: 𝐶/𝐷=0.15, 0.20, and 0.225. These configurations were tested at wind speeds of 6 and 8 m/s. Static torque was measured experimentally, alongside numerical calculations of flow and pressure distribution. A significant correlation between chord length and turbine performance was observed. The 𝐶/𝐷=0.20 profile exhibited increases of up to 50.27% and 58.88% in static torque at 6 and 8 m/s, respectively. The static torque coefficient increased from 0.0063 in the original profile to 0.0447 in the C/D=0.20 profile, directly contributing to the improvement of self-starting capability. Although the 𝐶/𝐷=0.20 geometry showed improvements, the C/D=0.225 profile did not show additional performance gains, indicating that further increases in chord length do not improve turbine performance. The profile modified with a 19.2% increase in thickness ranked just below the 𝐶/𝐷=0.2 profile, exhibiting torque increases of 41% and 25.22% at 6 and 8 m/s, respectively. These findings confirm that chord-to-diameter ratio adjustments play a critical role in boosting torque generation in vertical-axis wind turbines.

26 October 2026 in Computation
Verified
Journal Article
Open access
PDF file
RORogelio Martínez Oropeza
Rogelio Martínez Oropeza
JGJuan Carlos Garcia
Juan Carlos Garcia
Martin MorenoMartin Moreno
Martin Moreno
DGDulce M. Graciano
Dulce M. Graciano
MPMiguel Angel Basurto Pensado
Miguel Angel Basurto Pensado
APAndrés Pérez-Terrazo
Andrés Pérez-Terrazo
Vertical-axis wind turbines (VAWTs), including H-Darrieus rotors, are attractive for small-scale applications under variable wind conditions. Although airfoil-thickness effects have been examined for conventional NACA and other S-series profiles, systematic maximum-thickness variations of the symmetric S1046 airfoil remain insufficiently documented. This study therefore evaluates a three-bladed H-Darrieus turbine using the reference S1046 airfoil and six controlled maximum-thickness variations (−12.8%, −6.4%, +6.4%, +12.8%, +19.2%, and +32%). Transient two-dimensional URANS simulations, complemented by selected three-dimensional calculations, were performed in ANSYS Fluent 2020 R2 Fluent using the RNG k–ε turbulence model at a constant free-stream velocity of 6m/s and tested TSR values from 0.60 to 2.25. The corresponding local relative Reynolds number varied during rotor motion, with maximum values from 3.27×104 to 6.64×104 over the investigated TSR range. Among the tested configurations, the +19.2% thickness case produced the highest cycle-averaged power coefficient, CP¯=0.2692, comparable with 0.2589 for the reference S1046 airfoil, corresponding to an increase of 3.97%. The results indicate a non-monotonic thickness effect and identify +19.2% as the best-performing configuration among the discrete geometries investigated. The conclusions are restricted to the tested operating conditions and the adopted URANS numerical framework.