Ladle furnace slag (LFS), a by-product of steel refining, shows a promising reuse pathway as an alternative additive or substitute for Portland cement due to its high alkalinity and similar chemical composition to clinkers. However, LFS is often stored in large, open surface areas, leading to many environmental issues. To tackle waste management challenges, LFS can be recycled as supplementary cementitious material (SCM) in many cementitious composites. However, LFS contains some mineral phases that hinder its reactivity (dicalcium silicate (γ-C2S)) and pose long-term durability issues in the cured cemented final product (free lime (f-CaO) and free magnesia (f-MgO)). Therefore, LFS needs to be adequately treated to enhance its reactivity and ensure long-term durability in the structures of the cementitious materials. This literature review assesses possible LFS treatments to enhance its suitability for valorization. Traditional reviews are often multidisciplinary and explore all types of iron and steel slags, sometimes including the recycling of LFS in the steel industry. As the reuse of industrial by-products requires a knowledge of their characteristics, this paper focuses first on LFS characterization, then on the obstacles to its use, and finally compiles an exhaustive inventory of previously investigated treatments. The main parameters for treatment evaluation are the mineralogical composition of treated LFS and the unconfined compressive strength (UCS) of the final geo-composite in the short and long term. This review indicates that the treatment of LFS using rapid air/water quenching at the end-of-refining process is most appropriate, allowing a nearly amorphous slag to be obtained, which is therefore suitable for use as a SCM. Moreover, the open-air watering treatment leads to an optimal content of treated LFS. Recycling LFS in this manner can reduce OPC consumption, solve the problem of limited availability of blast furnace slag (GGBFS) by partially replacing this material, conserve natural resources, and reduce the carbon footprint of cementitious material operations.
Phosphate waste rock (PWR) is gaining attention as a potential alternative aggregate for concrete. Its valorization could reduce the environmental impacts of quarrying natural resources and stockpiling phosphate mining waste. This study comprehensively investigated the properties of fine and coarse aggregates produced from three rock types selected from PWR in Morocco: Flint, Phosflint, and Dolomite. A range of techniques was used to study their characteristics, including microstructural observations up to the microscale and X-ray computed tomography (X-CT), mineralogical and chemical compositions, physical and geotechnical properties such as Los Angeles (LA), micro-Deval (MDE), flexural strength, real dry density, and total porosity. The results showed that the coarse fractions of Flint, Phosflint, and Dolomite are code A or B of NF P 18-545 and exhibit good shape, density, and water absorption properties. Flint aggregates had the highest wear and fragmentation resistance with the lowest and finest porosity. They contained mainly quartz but also small proportions of Dolomite and fluorapatite. Phosflint aggregates had high resistance, shown by code A in LA and MDE values, and flexural strength equal to 17.1 MPa. They contained phosphate microfacies with a Ca/P atomic ratio equal to 1.8, cemented by cryptocrystalline silica. Dolomite aggregates’ mineralogical make-up consisted mainly of dolomite with the presence of quartz particles in addition to impurities. They also displayed significant total porosity (10–12%), as confirmed by X-CT. These findings were discussed to develop insights for the use of three types of PWR as alternative aggregates for concrete production. This investigation contributes to unveiling the properties of PWR as concrete aggregates and encourages circularity between the mining and construction sectors.
Les mélanges de ciment sulfoalumineux et de ciment Portland sont des liants hydrauliques innovants permettant de moduler les propriétés des bétons, telles que la vitesse de montée en résistance ou la stabilité dimensionnelle. Les performances du liant peuvent ainsi être ajustées pour de nombreuses applications. Au-delà de cet avantage, les émissions de dioxyde de carbone liées à la production du ciment sulfoalumineux sont significativement réduites comparées à celles du ciment Portland traditionnellement utilisé. La diversité des propriétés de ces liants résulte de la variété des mélanges pouvant être réalisés à partir des deux constituants de base. Chaque mélange présente alors une cinétique d'hydratation et des propriétés qui lui sont propres. Par exemple, certains liants sont expansifs mais présentent une montée en résistance progressive, tandis que d'autres sont stables dimensionnellement alors que leur résistance stagne après quelques jours d'hydratation. L'identification et le contrôle des paramètres à l'origine de ces comportements sont donc nécessaires pour garantir des propriétés spécifiques à un usage donné : chape, mortier de réparation, élément préfabriqué, etc. C'est l'objectif de cette étude qui s'attache à déterminer la cinétique, la minéralogie et les propriétés associées à l'hydratation de trois mélanges contenant 85 %, 70 % et 40 % de ciment Portland. Les essais entrepris ont aussi permis d'aboutir à une modélisation thermodynamique des mécanismes d'hydratation. L'impact de la composition du ciment Portland est également étudié. Enfin, il est montré que l'anhydrite et la chaux sont deux leviers qui modifient radicalement le processus d'hydratation et permettent ainsi d'adapter les propriétés d'un mélange aux exigences de son utilisation