Kauaʻi, an island within the Hawaiʻi archipelago, is home of a unique flora that contains 250 single-island endemic plant species. Threats have led to a significant population decrease where 97% of these plant species are now listed as endangered, critically endangered, or extinct. Vertical cliff habitats on Kauaʻi work as refugia to protect plants from their stressors. However, this habitat makes conservation work particularly difficult, forcing scientists, and botanists to use risky and time-consuming methods such as abseiling to access remote plant populations. Here we present the Mamba, the first aerial system capable of sampling plants on cliffs. This system is operated by two pilots and consists of an actively controlled platform suspended by a long cable under a lifting drone. Eleven otherwise inaccessible samples from five critically endangered species were collected during the first field trials on Kauaʻi Island. The samples are currently surviving in nurseries, demonstrating that the Mamba can be used to complete the conservation life cycle for organisms located in difficult areas, from location to collection, then cultivation and outplanting.
18 June 2020 in IEEE Robotics and Automation Letters
To extend the mission duration of smaller unmanned aerial vehicles, this letter presents a solar recharge approach that uses lakes as landing, charging, and standby areas. The Sherbrooke University Water-Air VEhicle (SUWAVE) is a small aircraft capable of vertical takeoff and landing on water. A second-generation prototype has been developed with new capabilities: solar recharging, autonomous flight, and a larger takeoff envelope using an actuated takeoff strategy. A 3D dynamic model of the new takeoff maneuver is conceived to understand the major forces present during this critical phase. Numerical simulations are validated with experimental results from real takeoffs made in the laboratory and on lakes. The final prototype is shown to have accomplished repeated cycles of autonomous takeoff, followed by assisted flight and landing, without any human physical intervention between cycles.
15 November 2018 in IEEE Robotics and Automation Letters
We present improvements to Sherbrooke's multimodal autonomous drone (S-MAD), a microspine-based perching fixed-wing UAV that enables thrust-assisted climbing along vertical surfaces. Aircraft models are used to predict the performance of various aerial climb regimes and to design a controller for wall distance tracking. It is found that fast, long, and vertical climbs are favorable. Both short and long vertical autonomous climb maneuvers are demonstrated on rough surfaces (e.g., brick, roofing shingles). Results show that the S-MAD compares favorably with existing climbers, reaching a specific resistance of 19 with a much faster vertical speed (i.e., 2 m/s). A reduction in S-MAD's aerodynamic drag and an improved motor efficiency could bring its specific resistance down to 7, at a vertical speed of 5 m/s.
This paper presents a modeling approach to capture the coupled effects of electrical–thermal aging in Li-ion batteries at the cell level. The proposed semi-empirical method allows for a relatively high accuracy and low computational cost compared to expensive computer simulations. This is something current models often lack but is essential for system level simulations, relevant for electric vehicle manufacturers. The aging analysis includes both cycling and calendar effects across the lifetime of the cell and reversible and irreversible heat in a lumped-mass model to capture the temperature evolution of the cell in operation. The Thévenin equivalent circuit model with capacitance used to simulate the electrical behavior of the cell was experimentally validated, showing a high correlation with the proposed model during the charging and discharging phases. A maximum error of 3% on the voltage reading was identified during discharge with the complete model. This model was also designed to be used as a stepping stone for a comprehensive model at the module and vehicle levels that can later be used by designers.
Effective methods for the design of high-performance electrical machines must use optimization techniques and precise and fast physical models. Convergence, precision and speed of execution are important issues, in addition to the ability to explore the entire domain of solutions. The finite element method (FEM) presents a high accuracy in the results but with high computational costs. Analytical models, on the other hand, solve the problem quickly but compromise the accuracy of the results. This work shows a comparison between an optimization made with an analytical electromagnetic model and a direct optimization with finite element field calculation for the optimal design of a Halbach array permanent magnet synchronous motor (PMSM). In the case of the analytical model, it is necessary to use an iterative method of correcting the model to obtain a valid solution. This method is known as Space Mapping (SM) and the analytical model can be improved with a reduced number of iterations with the FEM. The results show a rapid convergence towards an optimal solution for the SM, with more than 78% reduction in computational cost compared to a Direct FEM optimization. Both solutions have only a difference of 3% on the power density, which indicates that FEM does not improve the results obtained by SM. This represents a great advantage that allows for the consideration of a large amount of designs to analyze the domain of solutions in more detail. This study also shows that SM is a powerful method to optimize the power density or torque density of electrical machines.