To reduce energy consumption and increase energy efficiency in the building sector, thermal energy storage with phase change materials (PCMs) is used. The knowledge of the thermophysical properties and the characteristics of PCMs (like their enthalpy changes and the distribution of stored energy over a specified temperature range) is essential for proper selection of the PCM and optimal design of the latent thermal energy store (LHTES). This paper presents experimental tests of the thermophysical properties of three medium-temperature PCMs: OM65, OM55, RT55, which can be used in domestic hot water installations and heating systems. Self-made test chambers with temperature control using Peltier cells were used to perform measurements according to the T-history method. In this way the temperature range of the phase transition, latent heat, specific heat capacity, enthalpy and the distributions of stored energy of the three PCMs were determined. The paper also presents measurements of the thermal conductivity of these PCMs in liquid and solid state using a self-made pipe Poensgen apparatus. The presented experimental tests results are in good agreement with the manufacturers’ data and the results of other researchers obtained with the use of specialized instruments. The presented research results are intended to help designers in the selection of the right PCM for the future LHTES co-working with renewable energy systems, waste heat recovery systems and building heating systems.

The paper presents the results of the experimental and numerical analysis of a six-hole orifice flow meter. The experiments were performed on humid air in a 100 mm diameter duct. The aim of this research was to investigate the mass flow and pressure drop dependency in an orifice of a predetermined shape and to compare the results obtained with computational formulas recommended in the ISO 5167-2 standard for a single-hole orifice flow meter. The experiments and calculations were performed on several multi-hole orifice geometries with different contraction coefficient in a wide range of Reynolds numbers. The pressure was probed immediately upstream and downstream of the orifice. The flow coefficient determined for the six-hole orifice flow meter investigated was compared with the flow coefficient of conventional single-hole orifice with the same contraction coefficient. The results from computational formulas for single-hole orifice from ISO 5167 are also included in the paper. During some experiments, an obstacle has been introduced in the duct at variable distance upstream from the orifice. The effect of the thus generated velocity field disturbance on the measured pressure drop was then investigated. Numerical simulation of the flow with the presence of the obstacle was also performed and compared with experimental data.

Cutting wood with circular saws is a popular machining operation in the woodworking and furniture industries. In the latter sliding table saws (panel saws) are commonly used for cutting of medium density fiberboards (MDF), high density fiberboards (HDF), laminate veneer lumber (LVL), plywood and chipboards of different structures. The most demanded requirements for machine tools are accuracy and precision, which mainly depend on the static deformation and dynamic behavior of the machine tool under variable cutting forces. The aim of this study is to present a new holistic approach in the process of changing the sliding table saw design solutions in order to obtain a better machine tool that can compete in the contemporary machine tool market. This study presents design variants of saw spindles, the changes that increase the critical speeds of spindles, the measurement results of the dynamic properties of the main drive system, as well as the development of the machine body structure. It was proved that the use of only rational imitation in the spindle design on the basis of the other sliding table saws produced does not lead to the expected effect in the form of correct spindle operation.

Spray scrubbers are widely used in gas purification applications and allow fulfillment of the demands of air quality norms introduced all over the world. They effectively remove harmful gases like sulfur dioxide (SO₂), nitrogen oxides (NO_x), and particulate matter from industrial emissions, reducing their impact on air quality. Moreover, by capturing greenhouse gases such as carbon dioxide (CO₂) in certain applications, spray scrubbers contribute to efforts to reduce climate change. Optimization of scrubber internal elements leads to reduced energy usage and lowered water mass flow while maintaining high pollutant removal efficiency. This makes them cost-effective in the long term. The demister is an additional device which is often used in scrubbing systems, and its main task is to prevent the water droplets from escaping through the upper part of the scrubbing chamber. In this article, the pollution (MgO particles) is introduced to the system upstream the scrubber inlet, the working fluid is air under atmospheric pressure, and water droplets are generated by a single nozzle placed inside the scrubber. Before the experimental part, a preliminary numerical analysis of gas velocity inside scrubber is performed and expectations of particle behavior are indicated. Then, the authors present the spray scrubber laboratory stand designed by them and carry out experimental research on it. Each element of the test stand is described in the article including the self-designed fluidizer, which effectively mixes MgO powder with air. The authors investigate the effect of their innovative construction of demister on separation efficiency and compare the results to the case without demister. The impact of water mass flow rate generated by the nozzle and gas inlet velocity on separation efficiency is presented for several investigated cases. The results show that demisters significantly improve the separation efficiency at lower water mass flow rates and successfully prevent water droplets from reaching the scrubber outlet. The measured separation efficiency was in the range of 80% for lower water mass flow rates up to 97% for the highest water flows.

Sash gang saws with narrow-kerf saw blades are used in the production of glued laminate flooring elements in plants where dry technology is applied. This means that boards or friezes are sawn into top layer lamellae in dry conditions (moisture content of about 10–12%) from expensive wood species, often exotic. The object of this research was stellite-tipped teeth of narrow kerf saw blades sharpened under industrial conditions. A NIKON ECLIPSE Ti-S microscope equipped with a NIKON DS-Fi2 recording camera was used to take pictures of teeth, which were analysed in a graphical software to measure the radii of the main cutting edges. The high-quality images obtained were used to determine the values of the rounding radii of the cutting edges. It was noted that the quality of edges regenerated in industrial conditions, some of which had chipping, was lower than that of brand new saw blades.