Qiang Li

Dr. Qiang Li

orcid

Research Focus & Metrics

Academic Career Length

17Years (2010-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
6 September 2017 in Friction
Verified
Journal Article
Open access
PDF file
Valentin L. PopovValentin L. Popov
Valentin L. Popov
RPRoman Pohrt
Roman Pohrt
Qiang LiQiang Li
Qiang Li
The strength of an adhesive contact between two bodies can strongly depend on the macroscopic and microscopic shape of the surfaces. In the past, the influence of roughness has been investigated thoroughly. However, even in the presence of perfectly smooth surfaces, geometry can come into play in form of the macroscopic shape of the contacting region. Here we present numerical and experimental results for contacts of rigid punches with flat but oddly shaped face contacting a soft, adhesive counterpart. When it is carefully pulled off, we find that in contrast to circular shapes, detachment occurs not instantaneously but detachment fronts start at pointed corners and travel inwards, until the final configuration is reached which for macroscopically isotropic shapes is almost circular. For elongated indenters, the final shape resembles the original one with rounded corners. We describe the influence of the shape of the stamp both experimentally and numerically. Numerical simulations are performed using a new formulation of the boundary element method for simulation of adhesive contacts suggested by Pohrt and Popov. It is based on a local, mesh dependent detachment criterion which is derived from the Griffith principle of balance of released elastic energy and the work of adhesion. The validation of the suggested method is made both by comparison with known analytical solutions and with experiments. The method is applied for simulating the detachment of flat-ended indenters with square, triangle or rectangular shape of cross-section as well as shapes with various kinds of faults and to “brushes”. The method is extended for describing power-law gradient media.

1 October 2014 in Physical Mesomechanics
Verified
Journal Article
Closed access
PDF file
RPR. Pohrt
R. Pohrt
Qiang LiQiang Li
Qiang Li
The boundary element method as a numerical tool in contact mechanics is widely used and allows for surface roughness to be investigated with very fine grids. However, for every two grid points, influence coefficients have to be employed for every force-displacement combination. In this paper, we derive the matrixes of influence coefficients for the deformation of an elastic half space, starting from the classical solutions of Boussinesq and Cerruti. We show how to overcome complexity problems by using FFT-based fast convolution. A comprehensive algorithm is given for solving the case of dry Coulomb friction with partial slip. The resulting computer program can be used effectively in iterative schemes also in similar problems, such as mixed lubrication and notably improves the applicability of the boundary element method in contact mechanics.

29 January 2021 in Friction
Verified
Journal Article
Open access
PDF file
Valentin L. PopovValentin L. Popov
Valentin L. Popov
Qiang LiQiang Li
Qiang Li
ILIakov A. Lyashenko
Iakov A. Lyashenko
RPRoman Pohrt
Roman Pohrt
This paper is devoted to an analytical, numerical, and experimental analysis of adhesive contacts subjected to tangential motion. In particular, it addresses the phenomenon of instable, jerky movement of the boundary of the adhesive contact zone and its dependence on the surface roughness. We argue that the “adhesion instabilities” with instable movements of the contact boundary cause energy dissipation similarly to the elastic instabilities mechanism. This leads to different effective works of adhesion when the contact area expands and contracts. This effect is interpreted in terms of “friction” to the movement of the contact boundary. We consider two main contributions to friction: (a) boundary line contribution and (b) area contribution. In normal and rolling contacts, the only contribution is due to the boundary friction, while in sliding both contributions may be present. The boundary contribution prevails in very small, smooth, and hard contacts (as e.g., diamond-like-carbon (DLC) coatings), while the area contribution is prevailing in large soft contacts. Simulations suggest that the friction due to adhesion instabilities is governed by “Johnson parameter”. Experiments suggest that for soft bodies like rubber, the stresses in the contact area can be characterized by a constant critical value. Experiments were carried out using a setup allowing for observing the contact area with a camera placed under a soft transparent rubber layer. Soft contacts show a great variety of instabilities when sliding with low velocity — depending on the indentation depth and the shape of the contacting bodies. These instabilities can be classified as “microscopic” caused by the roughness or chemical inhomogeneity of the surfaces and “macroscopic” which appear also in smooth contacts. The latter may be related to interface waves which are observed in large contacts or at small indentation depths. Numerical simulations were performed using the Boundary Element Method (BEM).

20 July 2022 in Ceramics International
Verified
Journal Article
Closed access
XWXu Wang
Xu Wang
Valentin L. PopovValentin L. Popov
Valentin L. Popov
ZYZhanjiang Yu
Zhanjiang Yu
YLYiquan Li
Yiquan Li
JXJinkai Xu
Jinkai Xu
HYHuadong Yu
Huadong Yu

3 June 2019 in Proceedings of the Institution of Mechanical Engineers, Part J: Journal of Engineering Tribology
Verified
Journal Article
Closed access
PDF file
Qiang LiQiang Li
Qiang Li
RPRoman Pohrt
Roman Pohrt
ILIakov A Lyashenko
Iakov A Lyashenko
Valentin L. PopovValentin L. Popov
Valentin L. Popov
We present a new formulation of the boundary element method for simulating the nonadhesive and adhesive contact between an indenter of arbitrary shape and an elastic half-space coated with an elastic layer of different material. We use the Fast Fourier Transform-based formulation of boundary element method, while the fundamental solution is determined directly in the Fourier space. Numerical tests are validated by comparison with available asymptotic analytical solutions for axisymmetric flat and spherical indenter shapes.

17 July 2013 in Physical Review Letters
Verified
Journal Article
Closed access
PDF file
Qiang LiQiang Li
Qiang Li
MPMikhail Popov
Mikhail Popov
ADA. Dimaki
A. Dimaki
AFA. E. Filippov
A. E. Filippov
SKS. Kürschner
S. Kürschner
Valentin L. PopovValentin L. Popov
Valentin L. Popov
In this Letter, we study the friction between a one-dimensional elastomer and a one-dimensional rigid body having a randomly rough surface. The elastomer is modeled as a simple Kelvin body and the surface as self-affine fractal having a Hurst exponent H in the range from 0 to 1. The resulting frictional force as a function of velocity always shows a typical structure: it first increases linearly, achieves a plateau and finally drops to another constant level. The coefficient of friction on the plateau depends only weakly on the normal force. At lower velocities, the coefficient of friction depends on two dimensionless combinations of normal force, sliding velocity, shear modulus, viscosity, rms roughness, rms surface gradient, the linear size of the system, and the Hurst exponent. We discuss the physical nature of different regions of the law of friction and suggest an analytical relation describing the coefficient of friction in a wide range of loading conditions. An important implication of the analytical result is the extension of the well-known “master curve procedure” to the dependencies on the normal force and the size of the system.