Isomerization process became one of the best gasoline production sources, as it gives a high octane product while saving environment from pollution impacts. This paper presents a practical study that aims to improve the gasoline quality and economic income of an existing light naphtha isomerization unit used for octane improvement. The study included selecting the optimum combination of isomerization unit equipment that gives better product specifications for a specified feed. Eight scenarios were studied and simulated to predict the product specs. The original studied unit is MIDOR light naphtha isomerization unit at Alexandria-Egypt that recycles the unconverted hexane (C6). The other studied scenarios were adding fractionators for separating feed iso-pentanes, and recycling unconverted pentanes, hexanes and/or combinations of these fractionators. The results show a change in octane number of gasoline product for a specific feed. Once through process with no extra fractionators has lower octane number of 81 while that with de-iso-pentanizer–de-pentanizer and de-hexanizer produces gasoline with 92.3 octane number. Detailed economic study was done to calculate the return on investment “ROI” for each process option based on equipment, utilities, feed and product prices. Once through simple isomerization unit had the lowest ROI of 14.3% per year while the combination of De-iso-pentanizer with the De-hexanizer had the best ROI of 26.6% per year
Mono-ethylene glycol (MEG) is a high-volume chemical intermediate used as a raw material for a variety of chemical products. It could also be used as a hydrate inhibitor in natural gas. Recently, the importance of MEG has been increased due to its usage as a supporting emulsifier in diesel engines to reduce NOx and soot emissions, in addition to its usage as an additive to dual fuel diesel engines. The increase consumption of MEG in wide range of applications leads to the search for the most efficient, environmental friendly and cost effective technique to produce more quantities of it. MEG is most commonly manufactured via the hydration of ethylene oxide (EO). In this work, two different technologies of EO hydration to produce MEG are compared; the direct hydration of EO with water and the indirect hydration through the usage of ethylene carbonate (EC) as an intermediate. Comparative economic and environmental impact assessments were performed based on plant-scale simulations (per 600,000 tons per year of MEG produced) of the two hydration technologies using Aspen HYSYS version 11 simulation software. Economic analysis showed that the utilities’ energy consumption for direct hydration process is significantly higher than for indirect hydration by 279 megawatts. On the other hand, the environmental impact assessments showed that GHG emissions from natural gas power generation from utilities from direct hydration are three times greater than GHG emissions from indirect hydration. This leads to indirect hydration of ethylene oxide through ethylene carbonate formation being considered economically and environmentally preferable compared to the direct hydration process of ethylene oxide.
The increase of hydrogen demand has been one of the focal point recently. Indirect inter-plant hydrogen integration (IPHI) is a new issue for reducing hydrogen consumption and hydrogen discharge, in which hydrogen networks for different plants are integrated indirectly through centralized partitioning regeneration unit where hydrogen is regenerated for further reuse/recycle. This work is an extension of the automated targeting technique that was developed for single hydrogen network and the automated targeting that was developed for inter-plant water integration. The concentration cascade model has been developed to optimize hydrogen networks through partitioning regeneration unit such as pressure swing adsorption (PSA) or membrane separation. Two case studies from literature are studied to illustrate the applicability of the proposed model.
Carbon capture and storage (CCS) is a critical technology used for mitigating climate change by capturing carbon dioxide emissions from industrial sources and storing them underground to prevent their release into the atmosphere. Despite its potential, optimizing CCS systems for cost-effectiveness and efficiency improvement remains a significant challenge. In this paper, the optimization of CCS systems through the development and application of two mathematical optimization techniques is introduced. The first technique is based on using a superstructure optimization model, while the second technique relies on applying a goal programming optimization model. These models were solved using LINGO software version API 14.0.5099.166 to enhance the efficiency and cost-effectiveness of CCS systems. The first model, seeking to maximize the exchange of CO2 flowrate from sources to sinks, achieved a CO2 capture rate of 93.36% with an annual total cost of USD 1.175 billion. The second model introduced a novel mixed-integer non-linear programming (MINLP) approach for multi-objective optimization, targeting the minimization of total system cost, alternative storage, and unutilized storage while maximizing CO2 load exchange. The application of the second model, when prioritized to maximize CO2 flowrate exchange using the goal programming technique, resulted in a cost reduction of 36.46% and a CO2 capture rate of 75.87%. In contrast, when the second model prioritized minimizing the total annual cost, a 48% cost reduction was achieved, and the CO2 capture rate was decreased by 68.37%. A comparison of the two models’ results is presented. The results showed that the second model, with the priority of maximizing CO2 capture, provides the best economic–environmental objective balance, which offers notable cost reductions while keeping an efficient CO2 capture rate. This study highlights the potential of advanced mathematical modeling in increasing the feasibility of CCS as one of the very important strategies of mitigating climate change and reducing global warming.