Ramesh Babu Govindaraj

Mr. Ramesh Babu Govindaraj

orcid

Research Focus & Metrics

Academic Career Length

7Years (2020-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
9 February 2020 in Material Design & Processing Communication
Verified
Journal Article
Open access
PDF file
EJEva Junghans
Eva Junghans
RGRamesh Babu Govindaraj
Ramesh Babu Govindaraj
IAIsak Andersen
Isak Andersen
NWNorbert Worm
Norbert Worm
For additive manufacturing (AM) products such as structural and machinery components, the quality should be verified. In maritime industry, this task is performed by classification societies who are acting as independent third party and certifying such components. In the case of, eg, cast‐steel products, standards are available, which specify sampling procedures, properties, and destructive and nondestructive test methods as well as relevant material requirements for design purposes. For AM products, currently only few supportive standards are available. In tough market situation products must be cost‐efficient. Therefore, mandatory verification of products can only be enforced for vital applications. Unified, meaningful sampling and testing scopes are needed for application at different manufacturing locations and for evaluation by “no AM expert” staff. The impact of manufacturing defects in the AM process on the integrity on the AM product has to be evaluated. Contract partners may, or have to ask for evidence for the integritiy of AM products by certificates issued by third‐party institutions. DNV GL as a classification society has set up procedures for initial qualification and certification of AM products. This paper focusses on inspection and certification of AM maritime products and fit‐for‐purpose assessment.

Verified
Journal Article
Open access
PDF file
RGRamesh Babu Govindaraj
Ramesh Babu Govindaraj
IAIsak Andersen
Isak Andersen
ILInge Lotsberg
Inge Lotsberg
PLPer Rune Magnus Lindström Lussi
Per Rune Magnus Lindström Lussi
Wire arc additive manufacturing (WAAM) is increasingly being considered for large marine components because it offers design flexibility, reduced material waste, and potential benefits for manufacturing cost. However, the fatigue and fracture performance of WAAM materials in seawater remains insufficiently established for safety-critical applications such as marine propellers. This study evaluates the corrosion fatigue and fracture behavior of WAAM-manufactured 316L/316LSi austenitic stainless steel intended for propeller applications. A propeller-representative WAAM component was manufactured using gas metal arc welding, and fatigue specimens were extracted in both the weld and build directions. Axial fatigue testing was performed mainly in artificial seawater at stress ranges of 200, 250, 280, 300, and 330 MPa, with a test frequency of 5 Hz and a run-out criterion of 1 × 106 cycles. Chemical composition, ferrite prediction, hardness, Charpy impact behavior, S–N response, and SEM/EDS fractography were assessed to evaluate the impact on structural integrity. The deposited material showed a chemical composition consistent with 316L/316LSi stainless steel and an estimated ferrite content of approximately 8%, indicating a generally sound austenitic weld–metal microstructure. Several specimens reached run-out at stress ranges up to 250–300 MPa, whereas valid gauge-section fatigue failures occurred in higher stress ranges. Premature failures outside the gauge section were attributed to fixture-related effects and were not considered representative of intrinsic material behavior. SEM/EDS examination of a valid fatigue fracture identified an aluminum- and oxygen-rich crack-initiation feature consistent with an aluminum oxide inclusion. This observation indicates that the fatigue response of WAAM 316L/316LSi should be interpreted not only based on stress-life data but also using principles of fracture mechanics and damage tolerance, where surface or near-surface discontinuities may act as initial flaws and promote ΔK-driven crack growth in seawater. The results demonstrate promising fatigue performance within the experimentally validated range, but they also show that bulk mechanical properties alone are insufficient for qualifying WAAM propeller components. For the investigated WAAM process route, specimen surface conditions, stress ratio (R = 0.053), artificial seawater environment, and experimentally validated cycle range of up to 1 × 106 cycles, a preliminary engineering stress-range limit of Δσ = 200 MPa is recommended for pilot applications. This value should not be interpreted as a general design limit and should not be extrapolated to other WAAM processes, geometries, surface conditions, environments, stress ratios, or service-life regimes without additional qualification testing. Further high-cycle fatigue testing, mean-stress correction, fatigue crack-growth testing in seawater, fracture-toughness assessment, realistic defect-size characterization, non-destructive testing correlation, and component-scale validation are required before broader class acceptance of WAAM-manufactured propeller components.

10 July 2026 in International Journal of Fatigue
Verified
Journal Article
Open access
HBHagar El Bamby
Hagar El Bamby
VPVera Popovich
Vera Popovich
RGRamesh Babu Govindaraj
Ramesh Babu Govindaraj
MVMilan Veljkovic
Milan Veljkovic
TTTrayana Tankova
Trayana Tankova