Mihaela Iordachescu

Prof. Dr. Mihaela Iordachescu

orcid

Research Focus & Metrics

Academic Career Length

20Years (2007-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 September 2012 in Engineering Failure Analysis
Verified
Journal Article
Open access
MEM. Elices
M. Elices
AVA. Valiente
A. Valiente
LCL. Caballero
L. Caballero
MIMihaela Iordachescu
Mihaela Iordachescu
JFJ. Fullea
J. Fullea
VLV. López-Serrano
V. López-Serrano
Three broken steel bars from a sewed crack in a dam are reported. The inspection of the fracture surfaces of the prestressed bars suggests that fractures were triggered by small cracks and by the inherent brittleness of the bars, as fracture toughness was about 40MPam 1/2. The analysis of the failures shows that the usual design requirements for prestressing bars fail to warn against brittle failures if some damage exists. Some recommendations, based on the concept of damage tolerance, are suggested to avoid similar unfortunate incidents. © 2012 Elsevier Ltd.Peer Reviewe

1 January 2012 in Surface and Coatings Technology
Verified
Journal Article
Open access
MIMihaela Iordachescu
Mihaela Iordachescu
AVAndrés Valiente
Andrés Valiente
LCLuis Caballero
Luis Caballero
DIDanut Iordachescu
Danut Iordachescu
José L. OCAÑAJosé L. OCAÑA
José L. OCAÑA
JGJuan Antonio Porro González
Juan Antonio Porro González
Based on laser beam intensities above 109 W/cm2 with pulse energy of several Joules and duration of nanoseconds, Laser Shock Processing (LSP) is capable of inducing a surface compressive residual stress field. The paper presents experimental results showing the ability of LSP to improve the mechanical strength and cracking resistance of AA2024-T351 friction stir welded (FSW) joints. After introducing the FSW and LSP procedures, the results of microstructural analysis and micro-hardness are discussed. Video Image Correlation was used to measure the displacement and strain fields produced during tensile testing of flat specimens; the local and overall tensile behavior of native FSW joints vs. LSP treated were analyzed. Further, results of slow strain rate tensile testing of the FSW joints, native and LSP treated, performed in 3.5% NaCl solution are presented. The ability of LSP to improve the structural behavior of the FSW joints is underscored

1 April 2010 in Journal of Materials Processing Technology
Verified
Journal Article
Closed access
DID. Iordachescu
D. Iordachescu
MIMihaela Iordachescu
Mihaela Iordachescu
BGB. Georgescu
B. Georgescu
RMR.M. Miranda
R.M. Miranda
JRJ. Ruiz-Hervias
J. Ruiz-Hervias
José L. OCAÑAJosé L. OCAÑA
José L. OCAÑA

1 September 2014 in Construction and Building Materials
Verified
Journal Article
Open access
MAM. de Abreu
M. de Abreu
MIMihaela Iordachescu
Mihaela Iordachescu
AVA. Valiente
A. Valiente
The study brings new insights on the hydrogen assisted stress corrosion on damage tolerance of a high-strength duplex stainless steel wire which concerns its potential use as active reinforcement for concrete prestressing. The adopted procedure was to experimentally state the effect of hydrogen on the damage tolerance of cylindrical smooth and precracked wire specimens exposed to stress corrosion cracking using the aggressive medium of the standard test developed by FIP (International Prestressing Federation). Stress corrosion testing, mechanical fracture tests and scanning electron microscopy analysis allowed the damage assessment, and explain the synergy between mechanical loading and environment action on the failure sequence of the wire. In presence of previous damage, hydrogen affects the wire behavior in a qualitative sense, consistently to the fracture anisotropy attributable to cold drawing, but it does not produce quantitative changes since the steel fully preserves its damage tolerance

1 January 2018 in Construction and Building Materials
Verified
Journal Article
Closed access
MIMihaela Iordachescu
Mihaela Iordachescu
AVA. Valiente
A. Valiente
MPM. Pérez-Guerrero
M. Pérez-Guerrero
MEM. Elices
M. Elices

16 May 2021 in Metals
Verified
Journal Article
Open access
PDF file
Elena SCUTELNICUElena SCUTELNICU
Elena SCUTELNICU
MIMihaela Iordachescu
Mihaela Iordachescu
CRCarmen Catalina Rusu
Carmen Catalina Rusu
DMDanut Mihailescu
Danut Mihailescu
José L. OCAÑAJosé L. OCAÑA
José L. OCAÑA
This paper addresses the metallurgical and mechanical characterization of dissimilar joints made by laser autogenous welding between thin sheets of low-carbon steel (CS) and austenitic stainless steel (SS). The welding technology applied, previously optimized to produce sound dissimilar joints, is based on the heat source displacement from the weld gap centerline towards CS, in order to reduce the SS overheating. The research includes optical microscopy observations, energy dispersive X-ray analysis (EDX) to assess the wt% of Cr, Ni, and Fe in all regions of the dissimilar welded joint, hardness measurements, and tensile tests of transverse-welded flat specimens. In comparison with classical determination of the joint overall mechanical characteristics, the novelty of this research consists of experimental assessment of the local mechanical behavior of the fusion and heat affected zones by using a digital image correlation technique (VIC-2D). This is an efficient tool for determining the constitutive properties of the joint, useful for modelling the mechanical behavior of materials and for verifying the engineering predictions. The results show that the positive difference in yielding between the weld metal and the base materials protects the joint from being plastically deformed. As a consequence, the tensile loading of flat transverse specimens generates the strain localization and failure in CS, far away from the weld.