Gleb Permyakov

Dr. Gleb Permyakov

orcid

Research Focus & Metrics

Academic Career Length

12Years (2015-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
17 January 2025 in Metals
Verified
Journal Article
Open access
PDF file
DPDmitrii Panov
Dmitrii Panov
GPGleb Permyakov
Gleb Permyakov
SNStanislav Valentinovich Naumov
Stanislav Valentinovich Naumov
VMVladimir Mirontsov
Vladimir Mirontsov
EKEgor Alexeevich Kudryavtsev
Egor Alexeevich Kudryavtsev
GSGennady Salishchev
Gennady Salishchev
The microstructure, texture, and mechanical properties of Inconel 718 fabricated via hybrid wire-arc additive manufacturing (WAAM) with inter-pass forging, and the subsequent modified post-deposition heat treatment (PDHT), were investigated. The modified PDHT included homogenization at 1185 °C and double ageing at 720 °C, with furnace-cooling to 620 °C; this process was first used for Inconel 718 obtained via WAAM and inter-pass forging. In the as-printed material, two characteristic zones were distinguished, as follows: (i) columnar grains with a preferable orientation and (ii) fine grains with a random crystallographic orientation. The development of static recrystallization induced via inter-pass forging and further heating during the deposition of the next (upper) layer provoked the formation of the fine-grained zone. In the as-printed material, particles of (Nb,Ti)C and TiN, and precipitates of a Nb-rich Laves phase that caused premature cracking and failure during mechanical testing, were detected. In the PDHT material, two zones were found, as follows: (i) a zone with coarse uniaxial grains and (ii) a zone with a gradient grain size distribution. PDHT resulted in the precipitation of γ″ nanoparticles in the γ-Ni matrix and the dissolution of the brittle Laves phase. Therefore, significant hardening and strengthening, as well as increases in ductility and impact toughness, occurred.

20 August 2016 in The International Journal of Advanced Manufacturing Technology
Verified
Journal Article
Closed access
PDF file
TOTatiana V. Olshanskaya
Tatiana V. Olshanskaya
ESEkaterina S. Salomatova
Ekaterina S. Salomatova
VBVladimir Ya. Belenkiy
Vladimir Ya. Belenkiy
DTDmitriy Trushnikov
Dmitriy Trushnikov
GPGleb Permyakov
Gleb Permyakov

22 September 2021 in Russian Engineering Research
Verified
Journal Article
Closed access
PDF file
DTDmitriy Trushnikov
Dmitriy Trushnikov
GPGleb Permyakov
Gleb Permyakov
SVS. V. Varushkin
S. V. Varushkin
RDR. V. Davlyatshin
R. V. Davlyatshin
YBYu. V. Bayandin
Yu. V. Bayandin
SPShengyong Pang
Shengyong Pang
Vertical supply of a wire in surfacing by two electron beams is proposed as a process for three-dimensional product growth. The numerical modeling of this

15 December 2023 in PNRPU Mechanics Bulletin
Verified
Journal Article
Open access
PDF file
YBYu. V. Bayandin
Yu. V. Bayandin
DDD. S. Dudin
D. S. Dudin
AIA. V. Ilyinykh
A. V. Ilyinykh
GPGleb Permyakov
Gleb Permyakov
VCV. V. Chudinov
V. V. Chudinov
DTDmitriy Trushnikov
Dmitriy Trushnikov
To select rational parameters of the process of hybrid additive manufacturing of structures made of structural metal alloys and stainless steels, mechanical characteristics capable of serving as indicators of material quality were determined. The most advanced technologies of additive manufacturing by wire-arc surfacing (plasma, plasma arc with a melting electrode, including cold metal transfer) with layer-by-layer forging with a pneumatic impact tool and subsequent heat treatment were used. Aluminum-magnesium alloy AlMg5, titanium alloy Ti-6Al-4V, austenitic stainless steels 12Cr18Ni10Ti (AISI 321) and AISI 308LSi have been studied. Samples were cut from the blanks created by additive manufacturing – blades for standard tests for static uniaxial tension and cylinders for high-speed compression tests by the Kolsky method on a Hopkinson split bar. According to the registered and processed stress–strain curves for all materials, standard strength and ductility characteristics and the Johnson – Cook law of deformation and speed hardening were determined. For a correct assessment of the mechanical properties of additively produced materials, these tests were also carried out for each of them in the form of annealed rolled products. It is established that to compare the efficiency of various technological parameters of additive manufacturing, it is advisable to use static tensile strength and uniform elongation to rupture, having the smallest statistical variation. It was also found acceptable to approximate the Johnson – Cook law of the deformation curves of each of the studied materials according to averaged data, including various technological modes. Certain mechanical characteristics seem to be necessary for the search for effective modes of hybrid additive manufacturing and numerical calculation of various elastic-plastic problems in a dynamic formulation for the studied materials for design and technological needs.

1 February 2017 in IOP Conference Series: Materials Science and Engineering
Verified
Conference Paper
Open access
PDF file
DTDmitriy Trushnikov
Dmitriy Trushnikov
GPGleb Permyakov
Gleb Permyakov
This research examines the process of electron-beam welding in a keyhole mode with the use of beam oscillations. We study the impact of various beam oscillations and their parameters on the shape of the keyhole, the flow of heat and mass transfer processes and weld parameters to develop methodological recommendations. A numerical three-dimensional mathematical model of electron beam welding is presented. The model was developed on the basis of a heat conduction equation and a Navier-Stokes equation taking into account phase transitions at the interface of a solid and liquid phase and thermocapillary convection (Marangoni effect). The shape of the keyhole is determined based on experimental data on the parameters of the secondary signal by using the method of a synchronous accumulation. Calculations of thermal and hydrodynamic processes were carried out based on a computer cluster, using a simulation package COMSOL Multiphysics.

2 February 2015 in Modern Applied Science
Verified
Journal Article
Open access
TOTatiana Vasiljevna Olshanskaya
Tatiana Vasiljevna Olshanskaya
GPGleb Permyakov
Gleb Permyakov
VBVladimir Yakovlevich Belenkiy
Vladimir Yakovlevich Belenkiy
DTDmitriy Trushnikov
Dmitriy Trushnikov