Nely Georgieva

Dr. Nely Georgieva

orcid

Research Focus & Metrics

Academic Career Length

10Years (2017-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 January 2021 in IOP Conference Series: Materials Science and Engineering
Verified
Conference Paper
Open access
PDF file
NGNely Georgieva
Nely Georgieva
DSDelcheva Sivelina
Delcheva Sivelina
TPTsankov Petko
Tsankov Petko
In practice there are many processes that have complicated and complex character. Most often, these are dynamic systems with a large number of variable parameters, which significantly complicates their study, analysis and prediction. For their study most commonly used simulations that allow you to gain knowledge of their systemic nature. In these systems include and the thermodynamic systems where, due to a change of the many influencing parameters: temperature, pressure, velocity, fluid flow rate, various physical processes take place. For their study is widely used computer simulations to help predict the behaviour of systems under various conditions. Simulations are closely related to direct geometric modelling to enable to interactive design research and rapid model creation, allowing engineers to experiment with design ideas and immediately see the result of their changes. As an object of the simulation is most often fluid, structural and thermal simulation applications, which are used both for research and for innovative practical solutions in manufacturing enterprises. Computer simulations allow to predict the behaviour of certain processes in a real environment through virtual testing of CAD models. The main stages contain a methodical sequence, which includes the construction of a mathematical model, its numerical solution and processing of the obtained results. The main equations that make up the mathematical models are the balance equations of mass, momentum and energy, which determine the distribution of velocities, pressures, densities, temperatures and other control parameters. For modelling of flows of liquids and gases for industrial tasks, turbulence, heat transfer and chemical reactions, etc. are taken into account. In the practice, a large number of software solutions to simulate the processes occurring in thermal and fluid flows offered by many manufacturing companies are used. The aim of the present study is to analyse the possibilities of the software products used in practice to simulate the behaviour of dynamic fluid flows under certain initial conditions. Based on the analysis and the formulated conclusions, the choice of a software module for specific thermal research and construction of a geometric model of the studied objects through which numerical (CFD) simulations will be performed using different models, research in different modes of work, as well as the validation of the created methodologies, will be substantiated.

1 January 2021 in IOP Conference Series: Materials Science and Engineering
Verified
Conference Paper
Open access
PDF file
KIKrasimir Ivanov
Krasimir Ivanov
NGNely Georgieva
Nely Georgieva
STStanislava Tasheva
Stanislava Tasheva
VGVanya Gandova
Vanya Gandova
Survey energy efficiency of an industrial system was done. On the base energy audit, the consumption of energy and water was made analyse. On the following audit, there were made choices of energy saving measures, which would lead to proving and economy of energy in the industrial system and condition to work. The ultimate and primary energy savings for the industrial system, as well as CO2 emissions, were determined.

1 January 2023 in AIP Conference Proceedings
Verified
Conference Paper
Open access
PDF file
Vasil Ivanov HristovVasil Ivanov Hristov
Vasil Ivanov Hristov
NGNely Georgieva
Nely Georgieva
GBGeorgi Bonev
Georgi Bonev
Until recently the additive manufacturing (AM) was seen only as a design and testing tool but in the recent years it has become a regular manufacturing operatio


1 January 2023 in AIP Conference Proceedings
Verified
Conference Paper
Open access
PDF file
PTPetko Georgiev Tsankov
Petko Georgiev Tsankov
NGNely Georgieva
Nely Georgieva
Vasil Ivanov HristovVasil Ivanov Hristov
Vasil Ivanov Hristov
The design and optimization of gas systems is related to their hydraulic calculation. This article discusses the issue related to the hydraulic sizing of pneumatic and gas systems operating at medium pressures - pabs = 2… 5 bar, also defined as gas flows of compressible fluid. An overview of the classical theory, applied methods and models for the hydraulic sizing of the pipe networks during the movement of compressible fluids has been made. A methodology and a corresponding laboratory stand for research of such gas flows have been developed. Experimental results were obtained in determining the coefficient of linear resistance to the motion of a compressible fluid. A comparative analysis of the flows of "compressible - incompressible" gas has been made. The results regarding: the coefficient of linear resistance and its connection with the Reynolds number and the relative roughness of the pipeline have been confirmed and specified; the distribution of gas pressure along the pipeline during the flow of a compressible fluid. The specificity of the experimental work lies in the study of the movement of gas in small diameter pipelines, which allows both scientific and educational-laboratory and demonstration research.

15 April 2019 in Engineering review
Verified
Journal Article
Closed access
PDF file
NGNely Georgieva
Nely Georgieva
Zlatin ZlatevZlatin Zlatev
Zlatin Zlatev
MKMihail Karshakov
Mihail Karshakov
PPPavel Petrov
Pavel Petrov
In practice, movable blocks with oppositely arranged cutting inserts are used for turning internal and external cylindrical surfaces with great length. With these instruments, the dimension of dynamic adjustment is formed as a result of the continuous striving to the dynamic equilibrium of the radial components of both operation cutting forces which is restricted in the systems of the tool and the work piece. In this processing scheme, it is particularly important that the opposite cutting edges lie in a plane perpendicular to the axis of the work piece, which is difficult for implementation in certain circumstances. In addition, under certain circumstances, the variation of the machining allowance has an impact on the size of the dynamic adjustment. It leads to reduction of the diameter of the treated surface towards the dimension of the static adjustment of the block. This article proposes an innovative solution for using tools with opposite cutting inserts, which are axially displaced with guaranteed value to increase the accuracy of the obtained size. The question of adjusting the elasticity of the cutting block to compensate for the effect of the variable allowance on the accuracy of the treatment is investigated. As the result of researching, the dependencies to quantify from this impact and the conditions for its reduction are received, which can be used in practical conditions for increasing accuracy of the static adjustment.