Carbon dots (CDs) are widely used nanomaterials that not only exhibit good biocompatibility and photostability, but also benefit from a simple preparation process and easy functionalization, making them promising for broad applications in the fields of heavy metal ion detection and optoelectronic devices. Based on the excellent optical properties of CDs and the current situation of increasing energy shortages, this paper selects the natural polyphenolic compound tannic acid (TA) found in biomass materials as the carbon source and innovatively adopts a simple and convenient solvent-free pyrolysis method without auxiliary reagents or solvents. The CDs with good water solubility and certain fluorescence properties were directly prepared under the condition of high temperature, and the obtained CDs exhibited blue fluorescence, and a high QY of 35.4% was obtained at 300 °C. The analysis and results demonstrate the selectivity of these CDs for the detection of various metal ion solutions. In particular, these CDs are sensitive to Ni²⁺ and can be used as fluorescent sensors for the efficient and sustainable detection of Ni²⁺, whereas previous sensors were often specific to Fe³⁺ and Hg²⁺. Thus, a new sensing technique has been developed for the detection of Ni²⁺ to achieve more sensitive and rapid detection.

Carbon dots (CDs), as a new type of photoluminescent nanomaterial, have attracted extensive attention in various fields because of their unique luminescence properties. However, CDs will exhibit fluorescence quenching in the solid state or aggregate state, which limits their application. In this paper, a unique strategy is proposed to regulate solutions to achieve multicolour fluorescence of CDs in the solid state. We report the successful preparation of orange, green and blue solid fluorescent CDs using citric acid, urea and phenylethylamine as precursors and methanol, ethanol and water as solvents, respectively. The solid-state fluorescence of CDs may be caused by the linkage of the phenylethyl structure to the surface of CDs during formation, which effectively disperses the CDs and prevents π–π interactions between graphitized nuclei. Meanwhile, multicolour solid fluorescent CDs are realized by adjusting the solvent in the preparation process. Based on the excellent fluorescence properties of CDs, orange, green and blue light-emitting diodes (LEDs) are prepared. A white LED (WLED) can be obtained by mixing the three colours of solid fluorescent CDs, which shows the application potential of CDs in display lighting equipment.

Aiming to address the shortcomings of high-concentration ethanol or methanol extraction solutions that need to be diluted and concentrated prior to use in conventional macroporous resin adsorption approaches, an efficient approach for enrichment and purification of aucubin from the ionic liquid extraction solution of samaras of Eucommia ulmoides was proposed. Among the nine kinds of macroporous resins investigated, the HPD850 resin was found to be the most suitable. Equilibrium adsorption tests were investigated and found to be better fitted by the Langmuir isotherm model. After the dynamic tests on a column packed with HPD850, the optimum operational conditions were as follows: for the absorption process, an initial aucubin concentration of 9.87 mg/L, a sample volume of 13 bed volumes (BV), and a flow rate of 2 BV/h; for the water washing process, 5 BV of deionized water and a flow rate of 3 BV/h; for the ethanol desorption process, a 10–80% ethanol volume fraction as the eluent, 2 BV for each ethanol volume fraction, and a flow rate of 3 BV/h. The 40–80% ethanol volume fraction eluent was collected and concentrated to produce the final products, resulting in an aucubin purity and recovery of 79.41% and 72.92%, respectively.

The negative-pressure cavitation extraction (NPCE) technique was applied firstly to extract secoisolariciresinol diglucoside (SDG) from flaxseed cakes. The significant extraction parameters were screened by fractional factorial design (FFD). The optimal parameters were determined using the central composite design (CCD) with the two variables, NaOH amount and the liquid/solid ratio. The conditions of the extraction were optimized by using response surface methodology (RSM). Under the optimal conditions, the extraction yield and the extraction purity of SDG was 16.25 mg/g and 3.86%, respectively. The efficiency of NPCE was compared with that of conventional extraction methods. Our results demonstrated that NPCE was comparable to the well-known ultrasound-assisted extraction in term of extraction yield and purity. This extraction technique has advantages of less time-consuming, low solvent usage and high throughput capability.

Biomass carbon dots (CDs) have the characteristics of being green, nontoxic, inexpensive, and simple to prepare, and they can be used in luminescence-related fields. In this study, red, green, and blue luminescent CDs were synthesised by a simple hydrothermal method under alkaline, neutral, and acidic conditions using TA as carbon source and o-phthalaldehyde as blend. The unique optical properties of these CDs are due to the differences in their degrees of conjugation, which can be controlled by the pH value of the reaction system. These three kinds of biomass CDs have good applications in light-emitting diodes (LEDs). By mixing biomass CDs with epoxy resin, warm, and cold white LEDs with Commission Internationale de l’Elcairage (CIE) coordinates (0.35, 0.36) were successfully constructed on extremely stable multicolour CDs. This study shows that these biomass CDs are a promising material for white LED lighting.