A new method was developed for simultaneous determination of copper, lead, and cadmium, based on their voltammetric response at a carbon paste electrode modified with hexagonal mesoporous silica (HMS) immobilized quercetin (HMS-Qu/CPE). Compared with quercetin modified carbon paste electrode (Qu/CPE) and quercetin ionic liquid modified carbon paste electrode (Qu-IL/CPE), the HMS-Qu/CPE exhibited improved selectivity and high sensitivity toward the detection of copper, lead, and cadmium. The properties of the HMS-Qu/CPE in 0.1 M HCOONa-HCl buffer solution (pH4.7) were investigated by adsorptive stripping voltammetry (ASV) and electrochemical impedance spectroscopy (EIS). The electrochemical behavior of copper, lead, and cadmium at the modified electrodes and factors affecting the preconcentration procedures were also investigated. Detection limits of 5.0, 0.8, 1.0 nM for copper, lead, and cadmium were obtained, respectively. The method is simple, fast, sensitive, and selective, and is successfully applied to soil sample.
This work provides a comparative study of the dielectric and piezoelectric properties of randomly oriented and textured 0.88Na0.5Bi0.5TiO3-0.08K0.5Bi0.5TiO3-0.04BaTiO3 (88NBT) ceramics. Textured ceramics were fabricated by template grain growth (TGG) method using NaNbO3 (NN) for templates. For textured ceramics with 4 wt% NN templates, a Lotgering factor of 96% and piezoelectric coefficient d33 of 185 pC/N were obtained. Compared to the randomly oriented ceramics, textured ceramics show lower strain hysteresis (H = 7.6%), higher unipolar strain of 0.041% with corresponding large signal piezoelectric coefficient d33* of 200 pm/V at applied field of 2 kV/mm. This enhancement can be explained by the grain orientation along direction by texturing, where an engineered domain configuration is formed after polarization, leading to decreased hysteresis and increased piezoelectric property.
The impact of phase structure on piezoelectric performances of textured Na0.5Bi0.5TiO3 (NBT) based lead-free ceramics was studied, including 0.88NBT-0.08K0.5Bi0.5TiO3-0.04BaTiO3 (88NBT) with morphotropic phase boundary (MPB) composition and 0.90NBT-0.07K0.5Bi0.5TiO3-0.03BaTiO3 (90NBT) with rhombohedral phase. Both textured ceramics exhibit a high Lotgering factor, being on the order of f~96%. The piezoelectric coefficients of the textured 88NBT and 90NBT ceramics are increased by 20% and 60%, respectively, comparing to their randomly oriented ceramics. The piezoelectric enhancement of 90NBT textured ceramic is three times higher than 88NBT, revealing the phase structure plays a significant role in enhancing the piezoelectric performances of textured ceramics. Of particular significance is that the 90NBT textured ceramic exhibits almost hysteresis-free strain behavior. The enhanced piezoelectric property with minimal strain hysteresis is attributed to the poled rhombohedral engineered domain configuration.
Rapid, effective, and cost-effective methods for large-scale screening of pesticide residues in the environment and agricultural products are important for assessing potential environmental risks and safeguarding human health. Here, we constructed a novel aggregation-induced emission (AIE) electrochemical aptamer (Apt) sensor based on red-emissive sulfur quantum dots (SQDs), which aimed at the rapid screening and quantitative detection of malathion. SQDs were prepared using a two-step oxidation method with good electrochemiluminescence (ECL) optical properties. These SQDs were modified onto the electrode surface to serve as ECL luminophores. Subsequently, Apt was introduced and modified to form a double-helix structure with the complementary chain (cDNA). The ECL signal was reduced because the biomolecules had poor electrical conductivity and inefficient electron transfer. When the target malathion was added, the double helix structure was unraveled, the malathion Apt fell off the electrode surface, and the ECL signal was restored. The linear range of detection was 1.0 × 10−13–1.0 × 10−8 mol·L−1, and the detection limit was 0.219 fM. The successful preparation of the sensor not only develops the ECL optical properties of SQDs but also expands the application of SQDs in ECL sensing.