Nemanaj Latas

Mr. Nemanaj Latas


Research Focus & Metrics

Academic Career Length

4Years (2023-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
10 January 2025 in Gels
Verified
Journal Article
Open access
PDF file
NNNataša Mladenović Nikolić
Nataša Mladenović Nikolić
AKAleksandar Branislav Kandic
Aleksandar Branislav Kandic
JPJelena Potocnik
Jelena Potocnik
NLNemanaj Latas
Nemanaj Latas
MIMarija Ivanovic
Marija Ivanovic
Ljiljana KljajevicLjiljana Kljajevic
Ljiljana Kljajevic
The formation of an aluminosilicate gel structure made of alkali-activated materials (AAMs) was conducted through an alkali-activation reaction of the solid precursors (fly ash, metakaolin, and wood ash). Fly and wood ash are by-products of the burning process of coal and wood, respectively. Alkali-activated materials of aluminosilicate origin, made from the different ashes, fly and wood, are very attractive research targets and can be applied in various technological fields due to their thermal stability, resistance to thermal shock, high porosity, high sustainability, and finally, low energy loss during production. In this paper, we evaluate physico-chemical properties, microstructure, and radiological environmental impacts when wastes that contain elevated levels of naturally occurring radionuclides (NORs) such as fly ash and wood ash are made into “green cements” such as AAMs. The determination of radionuclide content was performed by means of gamma-ray spectrometry. Results showed that the AAMs have a lower value in the activity concentration of radionuclides than raw materials. The external absorbed gamma dose rate was 74.7–107.3 nGy/h, and the external radiation hazard index values were in range of 0.445–0.628 Bq/kg. The results of the activity concentration measurements for alkali-activated materials indicate the potential of their safe application in building construction. In terms of the structural characterizations, the obtained alkali-activated materials were examined using XRD, DRIFT, FESEM, and TEM analyses.

5 June 2025 in Applied Surface Science
Verified
Journal Article
Closed access
JPJelena Potocnik
Jelena Potocnik
NLNemanaj Latas
Nemanaj Latas
MMM. Milošević
M. Milošević
TJTamara Janakiev
Tamara Janakiev
Tijana StamenkovićTijana Stamenković
Tijana Stamenković
ISIrina Srejić
Irina Srejić

6 August 2024 in Colloids and Surfaces A: Physicochemical and Engineering Aspects
Verified
Journal Article
Closed access
VRVladimir Rajić
Vladimir Rajić
NLNemanaj Latas
Nemanaj Latas
DKDanilo Kisić
Danilo Kisić
KCKatarina Cvetanović
Katarina Cvetanović
MMMiloš Milović
Miloš Milović
MIMilutin Ivanović
Milutin Ivanović

1 September 2023 in Journal of the Electrochemical Society
Verified
Journal Article
Closed access
NLNemanaj Latas
Nemanaj Latas
NCNikola Cvjetićanin
Nikola Cvjetićanin
Anatase TiO2 was prepared in the form of nanotube arrays by anodic oxidation of Ti foil followed by annealing at 400 °C. Electrochemical experiments, which included cyclic voltammetry (CV), galvanostatic (GS) cycling and electrochemical impedance spectroscopy (EIS) were conducted in 1 M solution of LiClO4 in propylene carbonate (PC) at temperatures 25 °C–55 °C. CV experiments, at scan rates 5–50 mV·s−1, demonstrated with increasing temperature a large increase in the intensity of the redox peaks along with a decrease in the peak-to-peak separation. GS cycling showed large increase of capacity of thin-wall TiO2 nanotubes with increasing temperature, which attains 357 mAh·g−1 at 55 °C during lithiation at current rate 5.3 C, with capacity retention of 98.5% and Coulombic efficiency of 97.5%. Surface storage and development of secondary voltage plateau strongly contribute to such a large capacity value. EIS showed a multiple decrease in solid electrolyte interphase (SEI) layer resistance and charge transfer resistance with temperature rising up to 55 °C.

1 January 2024
Verified
Conference Paper
Open access
PDF file
VKVesna Krstić
Vesna Krstić
BTBiserka Trumić
Biserka Trumić
MMMilijana Mitrović
Milijana Mitrović
NLNemanaj Latas
Nemanaj Latas
MNMirjana Novaković
Mirjana Novaković
This paper details the the analysis of a Cu-Fe-P alloy, containing 0.003 wt% Fe and 0.014 wt% P, conducted using the X-ray diffraction (XRD) and selected area electron diffraction (SAED) techniques. The melted and homogenized Cu-Fe-P alloy was subjected to the extrusion and cold working (rolling) with different degrees of deformation. The required mechanical and structural characteristics of material were achieved by the mechanical and thermal processing of the alloy, where the working conditions of extrusion corresponded to the rolling with 75% deformation, recrystallization annealing at 470℃, annealing time of 150 min and cooling in a mixture of water and alcohol in the ratio 3:1. Both XRD and SAED results confirmed the presence of a crystalline structure. The observed reflections matched the cubic structure of the Cu phase, with no reflections detected for Fe, P, or their compounds, which is likely due to the low concentrations of these alloying elements.