This paper presents a novel method that uses the cold metal transfer based wire arc additive manufacturing process to fabricate functionally graded Inconel 825–SS316L walls. The optical micrograph of Inconel 825 exhibits continuous and discontinuous dendritic structures. The SS316L region comprises 5% of δ-ferrite in primary austenitic (γ) dendrites which was confirmed by the Creq/Nieq ratio of 1.305. The functionally graded interface reveals a partially mixed zone with a transition from the elongated dendrites to fine equiaxed dendrites. The tensile properties of the fabricated wall were determined at room temperature using specimens extracted from Inconel 825, SS316L, and the interface regions. The morphology of the tensile tested specimens revealed significant plastic deformation, indicating ductile failure. The fracture toughness of the wall was experimentally investigated by employing the crack tip opening displacement (CTOD) test. The fracture morphology exhibited a ductile mode of fracture with striations perpendicular to the direction of crack development. Elemental mapping revealed that there was no evidence of elemental segregation on the fractured surfaces, and the elements were uniformly dispersed. The CTOD measures 0.853 mm, 0.873 mm on the Inconel 825 side and the SS316L side respectively. The test results confirm that both the Inconel 825 and SS316L sides have good fracture toughness.
This research article addresses the pitting corrosion resistance of FGM walls fabricated by the Wire Arc Additive Manufacturing (WAAM). The wall is created by layer-by-layer transfer of molten metal in an uninterrupted manner with little heat input using the CMT process. Pitting corrosion tests were carried out as per the ASTM G48-11 standard on the specimens extracted from Inconel 825, FGM interfaces, and SS316L regions of the wall. The specimens were immersed in the ferric chloride hexahydrate solution for 24, 48, and 72 h. It was found that the FGM interface and the specimens made of Inconel 825 were more resistant to corrosion than the SS316L specimens. The weight loss is measured as 0.462 g, 0.1087 g, and 0.1349 g for the SS316L, FGM interface, and Inconel 825 specimens, respectively. Scanning Electron Microscopy (SEM) and Energy Dispersive Spectroscopy (EDS) were used to analyze the corrosion products at the corrosion pit. The order of the pitting corrosion resistance of the specimens extracted from the FGM wall was: FGM interface > Inconel 825 > SS316L.
In this work, Inconel 625 alloy was used to manufacture walls using the Wire Arc Additive Manufacturing (WAAM) technology, which is based on Gas Tungsten Arc Welding (GTAW). The wall was fabricated using a circular weave and stringer bead pattern. Microstructural analysis and tensile characteristics were evaluated for both walls. Using scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS), and elemental mapping, the fracture zones of the tensile specimens were examined. The microstructure is mostly made up of equiaxed dendrites, with the rare presence of continuous and discontinuous cellular dendrites along the cross-section. In tensile tests, circular weaved walls performed better than stringer bead walls. The circular weave specimen had an ultimate tensile strength (UTS) of 762 MPa in the horizontal and 722 MPa in the vertical orientations. Also, the Inconel 625 wall showed anisotropic behavior (5.3%) during tensile testing. The fracture morphology analysis revealed that all the specimens were fractured as a result of large plastic deformation, corresponding to ductile failure. Based on the EDS results, the fracture zone mainly consists of Ni and Cr with a small percentage of Nb and Mo. The absence of laves phases makes the fracture mode ductile. The elemental mapping shows uniform dispersion of Ni and Cr within the fracture region, further supporting the ductile failure mode.
The chapter highlights the significance of integrating IoT, AI, and advanced materials in sustainable manufacturing to promote eco-friendly practices and reduce environmental degradation. It highlights the synergy between these technologies, allowing real-time monitoring of resource utilization, energy consumption, and production efficiency. AI provides predictive analytics, promoting proactive maintenance and waste reduction. Advanced manufacturing techniques like additive manufacturing and composite materials reduce carbon footprints and resource depletion. Eco-friendly practices like recycling and renewable energy adoption promote sustainability throughout the supply chain, fostering a circular economy. However, technological barriers and regulatory constraints must be overcome.
1 July 2022 in Journal of Physics: Conference Series
The heat transfer performance of a flat plate solar water heating system was investigated experimentally in this paper (FPSWHS). The main objective of this investigation is to analyze the behaviour of FPSWHS with a 1.5 m2 receiver surface area in South Indian weather conditions and to calculate the heat energy created by the receiver for residential usages, which lessens electricity usage and assists the nation in conserving energy acquired from carbon fuels. Water was employed as the working medium in this investigation. The trials have been conducted in the first week of March 2021 at 13.0827° North, 80.2707° East. The findings confirmed that the solar thermal system's estimated average efficacy remained 44.3%, and the system's maximum output temperature of water was 67°C.