Fracture toughness is a critical indicator for the application of NiTi alloys in medical fields. We propose to enhance the fracture toughness of NiTi alloys by controlling the spatial grain size (GS) gradient. Utilizing rolling processes and heat treatment technology, three categories of NiTi alloys with distinct spatial GS distributions were fabricated and subsequently examined through multi-field synchronous fracture tests. It is found that the one with a locally ultra-high GS gradient (20 nm−3.4 μm) has significantly enhanced fracture toughness, which is as high as 412% of that of the normally distributed nano-grains with an average GS of 8 nm and 178% of that of the coarse-grains with an average GS of 100 nm. Theoretical analysis reveals that in such a gradient structure, phase transition in the coarse-grained matrix greatly absorbs the surface energy of subcritical and stable propagation. Meanwhile, the locally non-uniform GS distribution leads to deviation and tortuosity of the crack path, increasing the critical fracture stress. Furthermore, the nanocrystalline clusters distributed in the form of network nodes reduce the stress intensity factor due to their higher elastic modulus compared to the coarse-grained matrix. This work provides guidance for developing new gradient nanostructured NiTi alloys with high fracture toughness.
Solid state heat pumping using latent heat from first order ferroic phase transitions is a promising green alternative to traditional vapor compression technology. However, the intrinsic phase transition hysteresis poses a limitation on heat pumping energy efficiency. Here, we propose heat pumping using reversible heat from anhysteretic elastic deformation in martensitic phase of ferroelastic alloys. Conventionally, this thermoelastic effect (TeE) is considered too weak to be practical. But we find that in [100]-textured Ti78Nb22 martensitic polycrystals, the TeE can produce a large adiabatic temperature change (∆Tad) of 4−5 K at 413−473 K due to macroscopic large linear thermal expansion (αl = 10−4/K). This large TeE not only far exceeds those of ordinary metals (\(\Delta {T}_{{ad}}\approx 0.2K\)) but also brings a material-level energy efficiency that reaches about 90% of the Carnot theoretical limit. In other ferroelastic martensitic alloys with larger intrinsic αl (up to 5.4 × 10−4/K), the TeE is predicted to bring an even larger ∆Tad (up to 22 K) while maintaining relatively high efficiency. Our findings offer a non-phase-transition-based way for high efficiency solid state heat pumping.
Heating with less energy consumption and environmental impacts is a major challenge confronting the world. Solid-state heat-pumping using phase-transitional materials offer a promising green solution, but these materials′ coefficient of performance (COPmat) is only about 4 ~ 23, imposing an intrinsic restriction on the energy efficiency of developed devices. Here, we propose ultrahigh-efficiency heat-pumping via the reversible heat produced by anhysteretic linear elastic deformation of martensitic alloys. We discover that many of these alloys exhibit a large adiabatic temperature change (∆T_ad) when stressed along the crystallographic directions of intrinsic giant linear thermal expansion. Material-level heat-pumping through such thermoelastic effect is demonstrated using preferentially [100]-oriented Ti78Nb22 martensitic polycrystals, achieving a giant COPmat of 87 and a cyclically stable ∆T_ad of 5 K at 473 K. Our work opens a non-phase-transitional route towards energy-efficient solid-state heat-pumping.
Elastocaloric cooling (eC) uses shape memory alloys (SMAs) as energy-efficient, eco-friendly refrigerants. However, cost-effectively fabricating SMAs into fatigue-resistant, heat transfer–enhanced structures remains a key obstacle to commercialization of the eC technology. We introduce a “stamping and stacking” (S-S) method for producing porous, fatigue-resistant SMA structures. Honeycomb-like chips are stamped from nitinol (NiTi) thin sheets and then stacked into a layered tubular structure to increase heat exchange surface and at the same time avoid buckling and splitting failures encountered in existing SMA structures. The stacked structure endures >10 8 compression cycles and can deliver high specific cooling power of 3850 watts per kilogram. Our S-S method reduces fabrication costs by one order of magnitude compared with existing approaches, enabling mass production of eC refrigerant structures for commercial deployment.
Ferroelastic shape memory alloys (SMAs) with low functional fatigue during cyclic phase transition (PT) are crucial for elastocaloric cooling technology 1-4. However, this property is a long-standing challenge due to severe dislocation accumulation driven by the misfit stress in the boundary layer between the parent and the product (twinned martensite) phases5-7. Here, we find that nanometer-scale martensitic twin spacing can enable ultralow functional fatigue in single-crystalline Ni50Fe19Ga27Co4. It is revealed that the ultrafine twin spacing (1.6 – 3.2 nm) causes an ultrathin stressed boundary layer of 3 – 7 nm thickness, 10–103 times thinner than those of many other SMAs. This nanometer-scale thickness significantly limits the curvature radius of dislocation segments bent from Frank-Read sources, leading to strong line tension to suppress dislocation multiplication. Consequently, the alloy shows stable, large cooling capacity over 107 PT cycles. Our findings suggest a new route to develop ferroelastic materials with high functional stability by engineering nanotwins in the low-symmetry product phase.