Visible light as an excitation source is much more accessible than ultraviolet light, but the synthesis of lanthanide complex (LnC) films with visible-light excitation and high photoluminescence quantum yield (PLQY) is still a challenge. We report herein a visible light excitable and highly luminescent film by incorporation of a europium(III) (Eu3+) tetrakis(β-diketonate) complex with tetraphenylphosphonium as a counterion into a polymethyl methacrylate (PMMA) matrix. Excellent compatibility between the complex and PMMA was observed, resulting in the PMMA film with an 80 wt% loading content of the complex exhibiting a PLQY of up to 62.5% and a high transparency of ∼89%. As a proof-of-concept experiment, the luminescent film was used to fabricate luminescent solar concentrators (LSCs), in which the strong luminescence effect of the luminescent film is responsible for its optical conversion efficiency of 1.46% with a G of 1.87. This study presents a new model system for the development of highly transparent LSCs by utilizing high loading contents of LnCs.
The utilization of heat-shielding glazing technologies can efficiently promote carbon emission reductions and energy savings by decreasing solar irradiation into buildings. Although a variety of glazing technologies have been created for solar glazing, either the heat-shielding performance is low, the thermal stability is poor, or the cost is high. Here, we report a thermally stable heat-shielding coated glass for solar glazing in a simple way via direct calcination of Ce and Sb co-doped SnO2 nanoparticles with polysilazane (PSZ) coatings in air. The resulting coated glass has transmittances of 4.7% at 250–380 nm, 59.3% at 380–780 nm, and 9.7% at 780–2500 nm; excellent environment stability under accelerated aging conditions over 350 h; and also a ca. 50-fold lower fixed cost than commercial low-E glass. Moreover, a coated glass with a high pencil hardness of 9H was also fabricated via further spraying and calcinating of a PSZ coating as the cover layer, which is also the hardest coated solar glaze to our knowledge. The high solar-shielding performance and unprecedented low cost of the Ce and Sb co-doped SnO2-coated glass, as well as the simplicity of its fabrication, exhibit great potential in energy-saving buildings and cars.
Passive daytime radiative cooling (PDRC) technology with high solar reflectance and high infrared emissivity has been increasingly applied in green buildings. However, current PDRC designs are either high-cost or require additional multi-step fabrication processes, and both factors hinder their broader industrial application. Here, we present a low-cost, easy-to-process, scalable and uncomplicated porous epoxy-based radiative cooling coating via a simple Pickering high-internal-phase-emulsion (HIPE) approach. The obtained porous epoxy-based coating has micro- and submicropores. These hierarchical porous microstructures enable a synergistic interaction between the filler and the porous microstructure, thus enhancing the radiative cooling performance. As a result, the obtained porous epoxy-base polymer with alumina as fillers (PEP-A) coating presents a high solar reflectance of 95.6% in the wavelength range of 0.3–2.5 μm and a high infrared emissivity of 96.3% in the wavelength range of 8–14 μm, as well as a maximum subambient cooling temperature of 3.4 °C and an average cooling power of 105.6 W·m−2 under solar shortwave radiation of 123.01–134.67 W·m−2. Furthermore, the PEP-A coating can be easily applied via roll-coating, blade-coating, or brush-coating, and self-cures on diverse substrates like aluminum sheets, steel plates, polypropylene sheets, bricks, and wall surfaces without any additional template-extraction process. In particular, the cost of the raw materials for the PEP-A coating is 0.2–1.3% of that of previously reported radiative cooling coatings (e.g., Poly(vinylidenefluoride-co-hexafluoropropylene) and polydimethylsiloxane). The extraction-free nature, easy processability, self-curing ability, and low cost of the PEP-A coating make it very promising for large-scale PDRC production and applications.