Solid oxide fuel cells (SOFCs) have become promising devices for converting chemical energy into electrical energy. Altering the microstructure of cathode materials to enhance the activity and stability of the oxygen reduction reaction is particularly important. Herein, Pr0.5Ba0.5Co1−XNiXO3+δ with a tetragonal perovskite structure was synthesized through the sol–gel method. The polarization resistance of the symmetrical half-cell with Pr0.5Ba0.5Co0.9Ni0.1O3+δ as the cathode was 0.041 Ω·cm2 at 800 °C and 0.118 Ω·cm2 lower than that of the symmetrical cell with Pr0.5Ba0.5CoO3+δ as the cathode, indicating that the Pr0.5Ba0.5Co1−XNiXO3+δ cathode material had high catalytic activity during the electrochemical reaction. The results of electron paramagnetic resonance revealed that the concentration of oxygen vacancies increased as the Ni doping amount increased to 0.15. As a result of the increase in the Ni doping amount, the thermal expansion coefficient of the Pr0.5Ba0.5CoO3+δ cathode material was effectively reduced, resulting in improved matching between the cathode and electrolyte material. The power density of the single cell increased by 69 mW·cm−2. Therefore, Pr0.5Ba0.5Co1−XNiXO3+δ is a promising candidate cathode material for high-performance SOFCs.
Passive daytime radiative cooling (PDRC) technology with high solar reflectance and high infrared emissivity has been increasingly applied in green buildings. However, current PDRC designs are either high-cost or require additional multi-step fabrication processes, and both factors hinder their broader industrial application. Here, we present a low-cost, easy-to-process, scalable and uncomplicated porous epoxy-based radiative cooling coating via a simple Pickering high-internal-phase-emulsion (HIPE) approach. The obtained porous epoxy-based coating has micro- and submicropores. These hierarchical porous microstructures enable a synergistic interaction between the filler and the porous microstructure, thus enhancing the radiative cooling performance. As a result, the obtained porous epoxy-base polymer with alumina as fillers (PEP-A) coating presents a high solar reflectance of 95.6% in the wavelength range of 0.3–2.5 μm and a high infrared emissivity of 96.3% in the wavelength range of 8–14 μm, as well as a maximum subambient cooling temperature of 3.4 °C and an average cooling power of 105.6 W·m−2 under solar shortwave radiation of 123.01–134.67 W·m−2. Furthermore, the PEP-A coating can be easily applied via roll-coating, blade-coating, or brush-coating, and self-cures on diverse substrates like aluminum sheets, steel plates, polypropylene sheets, bricks, and wall surfaces without any additional template-extraction process. In particular, the cost of the raw materials for the PEP-A coating is 0.2–1.3% of that of previously reported radiative cooling coatings (e.g., Poly(vinylidenefluoride-co-hexafluoropropylene) and polydimethylsiloxane). The extraction-free nature, easy processability, self-curing ability, and low cost of the PEP-A coating make it very promising for large-scale PDRC production and applications.
Solid oxide fuel cells (SOFCs) have become promising devices for converting chemical energy into electrical energy. Altering the microstructure of cathode materials to enhance the activity and stability of the oxygen reduction reaction is particularly important. Herein, Pr0.5Ba0.5Co1-XNiXO3+δ with a tetragonal perovskite structure was synthesized through the sol–gel method. The polarization resistance of the symmetrical half-cell with Pr0.5Ba0.5Co0.9Ni0.1O3+δ as the cathode was 0.041 Ω·cm2 at 800 °C and 0.118 Ω·cm2 lower than that of the symmetrical cell with Pr0.5Ba0.5CoO3+δ as the cathode, indicating that the Pr0.5Ba0.5Co1-XNiXO3+δ cathode material has high catalytic activity during the electrochemical reaction. The results of electron paramagnetic resonance revealed that the concentration of oxygen vacancies increased as the Ni doping amount increased to 0.15. As a result of the increase in the Ni doping amount, the thermal expansion coefficient of the Pr0.5Ba0.5CoO3+δ cathode material effectively reduced, resulting in improved matching between the cathode and electrolyte material. The power density of the single cell increased by 69 mW/cm2. Therefore, Pr0.5Ba0.5Co1-XNiXO3+δ is a promising candidate cathode material for high-performance SOFCs.