Flow-induced motions (FIM) are an issue for floating offshore structures, such as multi-column platforms, as the phenomenon can decrease the fatigue life of the mooring, riser, and cable systems. The new concept of floating offshore wind turbines (FOWT) have a multi-column design that may be subjected to FIM. In the past, FIM was studied mainly for Oil & Gas platforms installed in deep waters. However, the FIM phenomenon of FOWT has been insufficiently explored. To rectify this, model tests were performed for the semisubmersible (SS) floating system design developed for the DeepCwind project (Offshore Code Comparison Collaboration Continuation (OC4) phase II). This paper will investigate the presence of FIM and show its importance in the design process of FOWT. Three different incidence angles of the current were tested, namely, 0, 90, and 180 deg. For each heading, 30 reduced velocities were tested, across the range 8000 < Re < 70,000. The results showed amplitudes in the transverse direction of around 70% of the diameter of the platform column, which is similar to those observed for deep-draft (DD) SS with circular columns. Note that these amplitude values are larger for a floater with a circular column, than for a platform with square columns. The results showed that as FIM occurred for this specific FOWT SS, its effect has to be considered in the mooring system and electric cable design.
5 February 2024 in Journal of Offshore Mechanics and Arctic Engineering
This work presents experimental results on vortex-induced vibration (VIV) of a horizontal cylinder with 2.69 m in length, 21 mm in diameter, and a mass ratio equal to 3.9. The experiments were carried out in a towing tank, where the flexible cylinder was towed under constant current profiles. Twenty reduced velocities were tested in a range of 1.75 < Vr < 15.79, corresponding to Reynolds numbers from 1000 to 10,000. The displacements were measured directly through a submerged optical system that simultaneously acquired the in-line and cross-flow movements of 18 reflective targets along the length. The extensive monitored section of the model enabled the application of a modal decomposition technique, which is a methodology that is still relatively unexplored through direct measurements. A comprehensive analysis was applied and the VIV responses related to amplitudes, frequencies, phase angles, and trajectories are shown and discussed in depth. The overall dynamics exhibits a multimodal response behavior, and the modal decomposition procedure has conclusively confirmed that the total amplitude comprises several modes vibrating at the dominant mode frequency. Root mean square values of response amplitude were up to 0.77D and 0.23D in the cross-flow and in-line directions, respectively. The cross-flow synchronization had a significant impact on the in-line excitation modes, and the trajectories showed coherence between motions.
Ship maneuvering prediction relies on hydrodynamic derivatives, traditionally obtained through empirical formulations based on hulls built decades ago. A comparison with experimental data revealed a notable discrepancy, particularly for the linear sway velocity derivative (), where these regression models inadequately capture the behavior of modern hulls. To overcome this limitation, a novel approach is proposed, in which 690 virtual static drift tests were conducted across a systematic series of 115 modern hull forms, parametrically generated in the Grasshopper platform and thus benchmarked against seven vessels. This extensive numerical dataset enabled the development of an updated regression formulation for , which was grounded in key geometric parameters and incorporated specific terms related to the bow and stern shapes. The results obtained by the CFD-based method were compared with those obtained experimentally, confirming the high fidelity of this approach, yielding a maximum relative error of only for the sway linear velocity derivative. Crucially, when this proposed empirical formula was integrated into a mathematical model (MM-TPN) to predict a ship’s trajectory, it demonstrated substantial improvement by reducing the absolute relative error in standard maneuvers from to compared with traditional methods used to describe the . Furthermore, an extensive discussion regarding the regression model was conducted, leading to the establishment of the drift angle threshold that invalidates the linear theory (set at for blunt hulls and for slender hulls). A comprehensive three-step validation process, encompassing the of the virtual static drift tests, validation of the derived maneuvering coefficient, and validation through standard maneuvers employing the novel approach proposed here, was fully executed.