Akbota Apsezhanova

Mrs. Akbota Apsezhanova


Research Focus & Metrics

Academic Career Length

3Years (2024-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
5 September 2024 in Coatings
Verified
Journal Article
Open access
PDF file
BRBauyrzhan Rakhadilov
Bauyrzhan Rakhadilov
NMNurtoleu Magazov
Nurtoleu Magazov
DKDauir Kakimzhanov
Dauir Kakimzhanov
AAAkbota Apsezhanova
Akbota Apsezhanova
YMYermakhan Serikuli Molbossynov
Yermakhan Serikuli Molbossynov
Aidar KengesbekovAidar Kengesbekov
Aidar Kengesbekov
Arc spraying is one of the most effective and cost-efficient thermal spraying technologies for creating high-quality protective coatings. This paper examines the influence of arc spraying process parameters on the properties of steel coatings. The parameters varied in this study included gas pressure, wire feed rate, and the distance from the spray gun to the substrate (standoff distance). Experimental evaluations focused on surface roughness, thickness, porosity, structure, and hardness of the coatings. The techniques used for these evaluations included profilometry for roughness measurement, scanning electron microscopy (SEM) for structural analysis, Vickers hardness testing, and optical microscopy. The results demonstrate a significant influence of arc spraying parameters on the characteristics of the resulting coatings. The analysis revealed that the coatings produced under different modes exhibit a layered structure and vary in thickness. A detailed examination of the coating structure identified defects such as unmelted particles, voids, and delamination in the interface zone. The study of coating thickness and porosity showed that increasing the wire feed rate and decreasing the standoff distance leads to the formation of thicker and denser coatings. Specifically, increasing the wire feed rate from 2 to 12 cm/s resulted in a decrease in porosity from 12.59% to 4.33% and an increase in coating thickness to 699 μm. The surface analysis highlighted the importance of a comprehensive approach to selecting the optimal roughness. While increasing the wire feed rate up to 12 cm/s can increase the Ra roughness parameter, gas pressure also significantly influences this parameter, reducing roughness from Ra = 18.63 μm at 6 MPa to Ra = 15.95 μm at 8 MPa. Additionally, it was found that varying the arc spraying parameters affects the hardness of the coatings, with all modes resulting in hardness values higher than that of the substrate. Therefore, optimizing these parameters enables the achievement of the best combination of mechanical and structural properties in the coatings. These findings can be valuable for further improvement of arc spraying technologies and the expansion of their application across various industries.

4 March 2025 in Coatings
Verified
Journal Article
Open access
PDF file
BRBauyrzhan Rakhadilov
Bauyrzhan Rakhadilov
Dastan BuitkenovDastan Buitkenov
Dastan Buitkenov
AAAkbota Apsezhanova
Akbota Apsezhanova
DKDauir Kakimzhanov
Dauir Kakimzhanov
ANAiym Nabioldina
Aiym Nabioldina
NMNurtoleu Magazov
Nurtoleu Magazov
This paper studies the coatings deposited on a 65G steel substrate by electric arc metallization using a 30KhGSA wire. The properties of the coatings obtained at 30 V, 40 V and 45 V are discussed, including their microstructure, porosity, microhardness, coefficient of friction and corrosion resistance. The experiments showed that the coatings possess a layered structure formed by sequential deposition of metal microdroplets. It was found that the increase in voltage favors the decrease in porosity, increase in layer density, increase in microhardness and improvement in wear resistance and corrosion resistance. At maximum voltage (45 V), there are optimum performance characteristics, such as minimal porosity (1.36%), high microhardness (305 HV) and improved corrosion resistance. The main defects of the coatings, including pores and oxide inclusions, which are formed during the sputtering process and depend on the kinetic energy of the microdroplets, were identified. These defects affect the mechanical and protective properties of the coatings.

20 June 2025 in Physical Sciences and Technology
Verified
Journal Article
Open access
PDF file
YMYermakhan Serikuli Molbossynov
Yermakhan Serikuli Molbossynov
BRBauyrzhan Rakhadilov
Bauyrzhan Rakhadilov
NMNurtoleu Magazov
Nurtoleu Magazov
AAAkbota Apsezhanova
Akbota Apsezhanova
AKArystanbek Kussainov
Arystanbek Kussainov
This study investigates the technological parameters of electric arc metallization applied to 30KHGSA steel, focusing on the effects of varying the spraying distance (100–250 mm) and gas pressure (6–9 Pa) on the resulting coating structure and properties. The spraying was performed using an SX-600 electric arc metallizer. Electron microscopy and metallographic analysis revealed that the coatings possess a layered structure consisting of solidified convective metal flows, micro-welded particles, and oxide inclusions. The optimal spraying parameters–150 mm distance and 7 Pa pressure–yielded the maximum coating thickness (729.58–733.62 μm) and the lowest porosity (4.02–4.33%). It was observed that increasing the spraying distance beyond 150 mm leads to reduced coating thickness, while deviations from the optimal gas pres sure result in decreased structural density and homogeneity. Electric arc metallization of 30KHGSA steel under optimal conditions enables the formation of coatings with enhanced wear resistance and mechani cal strength. Specifically, spraying distances over 150 mm and pressures outside the 7–8 Pa range nega tively affect the coating’s density, uniformity, and tribological performance. The identified optimal range (150–200 mm, 7–8 Pa) promotes the development of coatings with low surface roughness, reduced friction coefficient, and improved wear resistance. Key words: arc spraying, steel coatings, microstructure, Vickers hardness, porosity, thickness

19 September 2025 in Coatings
Verified
Journal Article
Open access
PDF file
AAAkbota Apsezhanova
Akbota Apsezhanova
BRBauyrzhan Rakhadilov
Bauyrzhan Rakhadilov
Dastan BuitkenovDastan Buitkenov
Dastan Buitkenov
NMNurtoleu Magazov
Nurtoleu Magazov
DKDauir Kakimzhanov
Dauir Kakimzhanov
Electric arc spraying is a promising technique for enhancing the wear resistance of components operating under abrasive and mechanical loads, particularly in agricultural soil-processing machinery. This study aims to comparatively analyze the properties of coatings formed using electric arc metallization with cored and solid wires of 30KhGSA and 51KhFA steel grades. Experimental investigations were carried out to evaluate the influence of wire type on the microstructure, microhardness, adhesion strength, and wear resistance of the sprayed coatings. Metallographic analysis and microhardness measurements revealed that coatings produced with cored wire exhibited a finer lamellar structure and higher hardness values compared to those formed with solid wire. Wear tests demonstrated improved resistance under abrasive conditions for cored wire coatings, indicating better performance under operational loads. The optimized spraying parameters were determined to ensure uniform and adherent coatings. The results suggest that using cored wire in electric arc spraying offers significant advantages in forming high-quality protective layers. These findings support the potential application of the developed coatings in extending the service life of soil-engaging machine parts under intensive field conditions.

30 September 2025 in Bulletin of Toraighyrov University. Physics & Mathematics series
Verified
Journal Article
Closed access
БРБ. К. Рахадилов
Б. К. Рахадилов
ДБД. Б. Буйткенов
Д. Б. Буйткенов
AAAkbota Apsezhanova
Akbota Apsezhanova
ANAiym Nabioldina
Aiym Nabioldina
МБМ. Б. Баяндинова
М. Б. Баяндинова
Метод дугового напыления считается одной из самых эффективных и экономичных технологий термического напыления, позволяющей создавать качественные защитные покрытия. В данной работе исследовано влияние параметров этого процесса на свойства стальных покрытий. В ходе эксперимента варьировались параметры: давление газа, напряжение, скорость подачи проволоки и расстояние от распылителя до подложки. В рамках исследования оценивались различные характеристики покрытий: шероховатость поверхности, толщина, пористость, структура и твёрдость. Для анализа использовались профилометрия (для измерения шероховатости), сканирующая электронная микроскопия (СЭМ), метод Виккерса для определения твёрдости и оптическая микроскопия для оценки пористости и морфологии покрытия. Результаты показали, что параметры напыления существенно влияют на окончательные свойства покрытия. Были проанализированы покрытия на основе стали 65Г, полученные методом электродуговой металлизации с использованием проволоки марки 30ХГС. Изучались такие характеристики, как микроструктура, пористость, микротвёрдость, коэффициент трения и коррозионная стойкость при напряжении 30 В, 40 В и 45 В. Выяснено, что покрытия формируются послойно за счёт осаждения микрокапель металла. Повышение напряжения способствует снижению пористости, увеличению плотности слоя, росту микротвёрдости и улучшению устойчивости к износу и коррозии. Наилучшие результаты достигнуты при напряжении 45 В: пористость снизилась до 1,36%, микротвёрдость достигла 305 HV, а коррозионная стойкость значительно повысилась. Также были выявлены основные дефекты, возникающие в процессе напыления – поры и оксидные включения. Ключевые слова: электродуговая металлизация, покрытие, сталь, структура, коррозия, проволока стальная наплавочная.

30 September 2025 in BULLETIN of the L.N. Gumilyov Eurasian National University. Physics. Astronomy Series
Verified
Journal Article
Open access
PDF file
МБМолдир Баяндинова
Молдир Баяндинова
BRBauyrzhan Rakhadilov
Bauyrzhan Rakhadilov
NMNurtoleu Magazov
Nurtoleu Magazov
AAAkbota Apsezhanova
Akbota Apsezhanova
В статье представлены результаты исследования свойств покрытий, полученных методом электродуговой металлизации на подложке из стали 65Г с использованием различных типов проволоки — литой и порошковой. Проведён сравнительный анализ влияния химического состава и технологических параметров напыления (скорость подачи проволоки, давление газа, дистанция напыления, предварительный нагрев подложки) на толщину, пористость, микротвёрдость, шероховатость и адгезию покрытий. Установлено, что порошковая проволока обеспечивает более низкую пористость, улучшенную однородность структуры и повышенную твёрдость по сравнению с литой проволокой. Оптимальные параметры режима напыления позволили достичь максимальной толщины покрытия до 712 мкм и минимальной пористости 4,3%. Результаты исследования подтверждают перспективность применения порошковых проволок для формирования износостойких и коррозионно-стойких покрытий в машиностроении и других отраслях промышленности.