The relevance of the application of hydraulic thruster technology is determined by the technological limitations of drilling both vertical and horizontal wells. The existing experimental studies confirm the effectiveness of the technology, but its widespread implementation is hindered by the lack of scientific foundations for its operation in combination with a downhole motor and bit. Our research methodology includes methods for analyzing scientific and technical information as well as methods of numerical modeling using programming languages and ready-made software packages for CFD calculations. Verification of the simulation results was carried out on the basis of the experimental field studies previously conducted with the participation of the authors of the article. This article presents the results of the analysis of the current state of the problem and computer physical and mathematical modeling of the work of the thruster together with the bit and downhole motor when drilling a deviated section of a well. Based on the simulation results, the expediency of using hydraulic thrusters in the practice of drilling wells with the possibility of predicting and operatively regulating the operation parameters of the “Hydraulic Thrusting Device—Downhole Motor—Bit” system is theoretically substantiated and scientifically confirmed.

Developing clean and renewable energy instead of the ones related to hydrocarbon resources has been known as one of the different ways to guarantee reduced greenhouse gas emissions. Geothermal systems and native hydrogen exploration could represent an opportunity to diversify the global energy matrix and lower carbon-related emissions. All of these natural energy sources require a well to be drilled for its access and/or extractions, similar to the petroleum industry. The main focuses of this technical–scientific contribution and research are (i) to evaluate the global energy matrix; (ii) to show the context over the years and future perspectives on geothermal systems and natural hydrogen exploration; and (iii) to present and analyze the importance of developing technologies on drilling process optimization aiming at accessing these natural energy resources. In 2022, the global energy matrix was composed mainly of nonrenewable sources such as oil, natural gas, and coal, where the combustion of fossil fuels produced approximately 37.15 billion tons of CO₂ in the same year. In 2023, USD 1740 billion was invested globally in renewable energy to reduce CO₂ emissions and combat greenhouse gas emissions. In this context, currently, about 353 geothermal power units are in operation worldwide with a capacity of 16,335 MW. In addition, globally, there are 35 geothermal power units under pre-construction (project phase), 93 already being constructed, and recently, 45 announced. Concerning hydrogen, the industry announced 680 large-scale project proposals, valued at USD 240 billion in direct investment by 2030. In Brazil, the energy company Petroleo Brasileiro SA (Petrobras, Rio de Janeiro, Brazil) will invest in the coming years nearly USD 4 million in research involving natural hydrogen generation, and since the exploration and access to natural energy resources (oil and gas, natural hydrogen, and geothermal systems, among others) are achieved through the drilling of wells, this document presents a technical–scientific contextualization of social interest.

Optimizing the drilling process is critical for the exploration of natural resources. However, there are several mechanic parameters that continuously interact with formation properties, hindering the optimization process. Rate of penetration (ROP) and mechanical specific energy (MSE) are considered two key performance indicators that allow the identification of ideal conditions to enhance the drilling process. Thus, the goal of this research was to analyze field data from pre-salt layer operations, using a 2D analysis of parameters as a function of depth, response surface methodology (RSM), and multi-objective optimization. The results show that the RSM method and multi-objective optimization provide better results when compared with 2D analysis of parameters as a function of depth. The RSM method can be used as a tool to analyze the effects of the independent drilling mechanical parameters (WOB, RPM, FLOW, and TOR) on the response variables (ROP and MSE) with a 95% confidence level. Through multi-objective optimization, it was possible to concomitantly achieve an ROP of approximately 22 ft/h and MSE of nearly 11 kpsi using the values of WOB, RPM, FLOW, and TOR of about 11 klb, 109 rev/min, 803 gpm, and 3 klb-ft, respectively. Using high WOB values, i.e., from the mean value up to the maximum value of approximately 43 klb, reflects a low ROP and most likely indicates an operation beyond the foundering point. High FLOW promotes a more efficient hole cleaning and higher rates of cuttings transport, thus preventing eventual in situ drill-bit sticking. Flow adjustment also ensures an adequate balance of dynamic bottom hole pressure, in addition to controlling the force impact force of the drilling fluid in contact with the rock being drilled, expressing importance in terms of efficiency and rock penetration. Finally, it is important to mention that the results of this research are not only applicable to hydrocarbon exploration but also to geothermal and natural hydrogen exploration. Values analyzed and presented with decimal precision should be logically focused as integers when in industrial application.

Nowadays, the exploration of different deep subsurface energy-related natural resources (oil/gas, natural hydrogen, geothermal, among others) is gaining importance. The exploration of these deep subsurface resources can present several challenges, such as complex lithology to be drilled, high depth to be reached, and considerable rock hardness, among others. In this context, the implementation of methodologies focused on real-time operational efficiency improvement has gained attention. Mechanical specific energy (MSE), rate of penetration (ROP), and even vibrations are key indicators that can be combined and used for drilling process optimization and efficiency improvement. These indicators are linked to operational drilling mechanic parameters, such as weight on bit (WOB), rotary speed (RPM), torque (TOR), and flow rate (FLOW). Despite this, multi-objective research considering both MSE and torsional vibration (stick–slip) has been largely overlooked in drilling optimization studies. Therefore, the main objective of this paper is to analyze field data from carbonate reservoirs using a multi-objective optimization approach based on torsional vibration, by means of stick–slip and MSE analyses. The focus is to minimize MSE values and mitigate stick–slip using self-developed decision matrices which consider WOB, RPM, and FLOW as key elements. The research results demonstrated that FLOW is a crucial parameter for minimizing torsional vibrations and should be prioritized in drilling operations, also for mitigating undesirable events. The optimization process yielded optimal WOB values for each RPM range (from 100 to 180 [rev/min]) and FLOW range (from 2200 to 3900 [L/min]). The decision matrix revealed that regions with high desirability correspond to high RPM (above 120 [rev/min]), with WOB varying from 5 to 13 [tf], and FLOW rates above 2300 [L/min]. Critical drilling conditions occur when low RPM, low FLOW, and high WOB (above 13 [tf]) are applied, as these conditions and this combination of parameters are most susceptible to release severe torsional vibrations, indicating a higher risk of operational problems.

Several methods exist for data transmission during deep drilling albeit with inherent drawbacks. Amongst these, the most common method for data transmission in deep boreholes remains “Mud Pulse Telemetry” which sends information through the drilling mud inside the drill string by means of coded pressure pulses. Due to the limitation in data transmission rate, efforts have been on to seek ways of improving data transmission rate in Mud Pulse Telemetry. One of such efforts is exploring the plurality of Mud sirens for signal amplification and increased data transmission rate. The objective of this research is to push the boundaries of the plurality of mud sirens beyond theories into practical experiments. Investigation was done on the Multi-frequency mud siren concept by simulations and practical experiments within the specially built flowloop facility in the Institute for Drilling Engineering and Fluid Mining, Technische Universitat Bergakademie Freiberg. Various scenarios, frequencies, timeslots and set-up configurations (series and parallel) were explored. Numerical simulation was done using ANSYS CFX and resulting signals were duly processed and analyzed with MATLAB. The paper displays results of the simulation and experiment establishing the theory of signal amplification and increase in data transmission rate via the multi-frequency mud siren concept.