The main interest in the valorization of vegetable wastes is due to the peculiarity of their chemical composition in substances that present important properties. Among these substances, antioxidants could replace those industrially manufactured. In the present study, three solvents of different polarities (hexane, ethanol, and water) were applied for the extraction of phenolic compounds from Cynara cardunculus L. waste using two extraction methods: Soxhlet Extraction (SE) and Ultrasonic-Assisted Extraction (UAE). The obtained extracts were then characterized by Fourier-Transform Infrared (FTIR) spectroscopy and spectrophotometric determination of Total Phenolics (TPC), Total Flavonoids (TFC), and Condensed Tannins (CT). Total Antioxidant Capacity (TAC) and 2,2-diphenyl-1-picrylhydrazyl (DPPH) free radical scavenging activity of ethanol and water extracts of leaves and stems were also evaluated. High extraction yields were obtained by UAE. Water extracts had high yield regardless of the technique used for leaves and stems, and these extracts showed high TAC of 534.72 ± 3.83 mg AAE/g FM for leaves and 215.70 ± 8.87 mg AAE/g FM (mg of ascorbic acid equivalent per g of FM) for stems, and IC₅₀ of 2077.491 μg/mL for leaves and 1248.185 μg/mL for stems. We explain the latter by the high total phenolic contents (TPCs), which reach 579.375 ± 3.662 mg GAE/g FM (mg of gallic acid equivalents per g of fresh matter) for leaves and 264.906 ± 3.500 mg GAE/g FM for stems. These results confirmed that the leaves and stems of the studied cardoon waste were, indeed, interesting sources of natural antioxidants.

The removal of heavy metals from wastewater has become the subject of considerable interest at present. Thus, the use of novel adsorbents that are highly efficient is of critical importance for the removal of Cr (VI) ions from aqueous media. The adsorption of Cr (VI) ions from aqueous solutions by a new adsorbent, cedar wood sawdust, and the optimization of its adsorption parameters, were investigated in this study. Cedar wood sawdust was used in its native and HNO₃/NaOH chemically modified forms as new low-cost sorbents to remove Cr (VI) ions from aqueous solutions in a batch system. The adsorption conditions were analyzed via response surface methodology. The RSM results showed that the optimal adsorption conditions yielding the best response were an adsorbent mass of 2 g for native Cedar and 1.125 g for its activated form, a metal concentration of 150 mg/L for native Cedar and 250 mg/L for activated, a temperature of 50 °C, a pH of 1, and a contact time of 67.5 min. At optimum adsorption conditions, the maximum adsorption capacities and the adsorption yields were 23.64 mg/g and 84% for native Cedar and 48.31 mg/g and 99% for activated Cedar, respectively.

Biobased foams have the potential to serve as eco-friendly alternatives to petroleum-based foams, provided they achieve comparable thermomechanical and physical properties. We propose a facile approach to fabricate eco-friendly cellulose nanofibril (CNF)-reinforced thermomechanical pulp (TMP) fiber-based foams via an oven-drying process with thermal conductivity as low as 0.036 W/(m·K) at a 34.4 kg/m³ density. Acrodur^®, iron chloride (FeCl₃), and cationic polyacrylamide (CPAM) were used to improve the foam properties. Acrodur^® did not have any significant effect on the foamability and density of the foams. Mechanical, thermal, cushioning, and water absorption properties of the foams were dependent on the density and interactions of the additives with the fibers. Due to their high density, foams with CPAM and FeCl₃ at a 1% additive dosage had significantly higher compressive properties at the expense of slightly higher thermal conductivity. There was slight increase in compressive properties with the addition of Acrodur^®. All additives improved the water stability of the foams, rendering them stable even after 24 h of water absorption.

This study aimed to develop four adsorbents, neat and activated, from the cardoon leaves and stems. The developed adsorbents were first analyzed to determine the surface acid–base properties using Boehm’s method, pH at zero charge point, iodine and methylene blue values, and moisture, ash, and fixed carbon contents. They were also characterized by scanning electron microscopy coupled with energy-dispersive X-ray analysis, X-ray diffraction, Fourier transform infrared absorption spectroscopy, thermogravimetric analysis, and inductively coupled plasma atomic emission spectroscopy. After that, these adsorbents were applied for adsorption of an organic dye “brilliant green” (BG), and the effect of various parameters on the adsorption efficiency was evaluated. The obtained results revealed the differences between the adsorbents derived from the neat cardoon leaves and stems and their activated carbon in terms of properties and BG adsorption efficiency.