The external walls of a building represent the interface between the interior and exterior environments. Insulating external walls represents the most cost-effective means of ensuring indoor comfort. Despite the prevailing assumption that insulation will increase the cost of the building, this study has demonstrated that this is not the case. Notwithstanding the increase in investment costs, the application of insulation to the external walls has been demonstrated to result in a reduction in fuel consumption and operating costs. In accordance with TS 825, there are five distinct degree-day zones, with the requisite heat loads in these zones exhibiting variability. Accordingly, a cost-based methodology is required to ascertain the optimal insulation thicknesses for the various degree-day zones. In this study, the gains to be obtained in the case of using three different insulation materials for five different wall types to be used in the buildings to be built instead of the buildings destroyed in the earthquake in Turkey in 2023 were analyzed. Samples from three degree-day zones affected by earthquakes were assessed for insulation, wall structures, and fuel types. The study assesses optimum insulation thickness, investment cost, annual fuel savings, annual economic benefits, and investment payback period.
10 March 2020 in Energy Sources, Part A: Recovery, Utilization, and Environmental Effects
Energy consumption in the textile industry is a significant part of the production cost. A shell-and-tube heat exchanger (STHX) was designed and manufactured for waste energy recovery from a hot-oil boiler in a textile finishing factory. An STHX with a single pass, including finned tubes and no baffle, was manufactured. By providing waste energy recovery to the applied system, air is released to the environment at 323 K instead of 525 K. Two scenarios were analyzed: (i) the designed STHX, alternatively with finned and unfinned-tube designs; and (ii) a double-pipe heat exchanger (DPHX) under the same operating conditions. These two cases were compared in terms of thermal performance. The applied system achieved an energy recovery of approximately 74.2%. The application of finned-tubes has an effect of between 11% and 24% on the total heat transfer coefficient. Applying the DPHX would provide thermal energy recovery of approximately 13% under the same operating conditions. The reason for the greater waste energy recovery when applying STHX is also shown by this analysis. Abbreviations: NTU: number of transfer units
12 August 2024 in Eskişehir Osmangazi Üniversitesi Mühendislik ve Mimarlık Fakültesi Dergisi
Bu çalışmada, havacılık sektöründe karbon ayak izinin belirlenmesi ve azaltılması ile ilgili örnek bir uygulama yapılmıştır. Uygulamada, Eskişehir ilinde faaliyette olan Hasan Polatkan Havalimanı’nın 2023 yılındaki uçuşları baz alınarak karbon ayak izi hesaplanması amacıyla bir süreç gerçekleştirilmiştir. Çalışmada, emisyon hesaplamalarında Hükümetler Arası İklim Değişikliği Paneli tarafından tavsiye edilen Tier yaklaşım metodu kullanılmıştır. Ulaştırmadan kaynaklanan 〖CO〗_2 emisyon miktarı 2023 yılı Hasan Polatkan Havalimanı’nında 6.893.160 kg olarak hesaplanmıştır. Sonuç olarak; havayolu ulaştırma sektöründe kullanılan uçakların üreticileri ile düzenleyici kurumlar arasında sürdürülebilirlik konusunda bir standardizasyonun acilen sağlanmasının gerekli oluğu tespit edilmiştir.
9 June 2016 in Mugla Journal of Science and Technology
In this study, a computer model of the Zalman ZM-WB3 Gold heat exchanger which is one of the liquid-cooled computer processors in the market has been generated and the model has been confirmed by the previous researchers models and experimental data. Then, the fin thickness and heights of the same heat exchanger and the type of liquid fluid in which the heat exchanger operates have been changed. The CFD analyzes of the new models were performed by using Ansys Fluent 17.1 program. Following that, nano heat removal (cooling) performances were investigated with models using rectangular fin fluid heat exchangers with different fin heights of 5 mm, 5.5 mm and 5.7 mm, and different fin thicknesses of 1.2 mm, 1.4 mm, 1.6 mm, 1.8 mm and 2 mm, and different fluids as water, copper oxide-water (CuO-H2O) nanofluids with volume ratios of 2.25% and 0.86%, and graphene oxide (GO-H2O) nanofluid with the volume ratio of 0.01%. It was concluded that the best CPU cooler performance could be achieved by using CuO - H2O as nanofluid with a volumetric ratio of 2.25% with a heat exchanger that has a 5.5 mm fin height and 2.0 mm fin thickness.