Sugar cane bagasse ash (SCBA), a by-product of sugar and alcohol production, is one of the potential pozzolanic material that can be blended with Portland cement. In this study, SCBA with particle sizes <45 μm was used to replace type I ordinary Portland cement with various dosages (10%, 20%, and 30%) by weight of binder. The water/cementitious material (w/cm) and sand/binder ratios were kept at constants of 0.55 and 2.75, respectively. Composites were mixed, and effects of SCBA on properties were investigated by conducting flow test, water absorption test, initial surface absorption test, drying shrinkage test, compressive strength test, rapid chloride penetration test (RCPT), thermal gravimetric analysis (TGA), and scanning electron microscopy (SEM). Experimental results show that the flow spread of fresh mortars would decrease with an increase of SCBA replacement. The specimens with 10% SCBA have the superior performance on compressive strength, drying shrinkage, water absorption, initial surface absorption, and chloride ion penetration, TGA, and SEM at the age of 56 days. It indicates that 10% cement replacement of SCBA may be considered as the optimum limit.
1 February 2015 in International Journal of Engineering and Technology
The aim of this study was to investigate the effect of montmorillonite as additive on the properties of cement paste and mortar. Montmorillonite was used at 0%, 5%, 10% and 15% additive by weight of cement, and the water/cement ratios of 0.45 and 0.55 are considered for the cement pastes and cement mortars with the sand/cement ratio of 1, respectively. Experimental results indicate that the use of montmorillonite as cement additives increases the compressive strength except the specimens containing 15% montmorillonite at the age of 28 days. The water absorption and initial surface absorption decreased with the increase of montmorillonite additives for the cement pastes. However, the cement mortars had an opposite test result in water absorption and initial surface absorption. The cement pastes and mortars containing montmorillonite have higher adsorption-desorption values than those of the plain cement pastes and mortars. Meanwhile, scanning electron microscopy and mercury intrusion porosimetry tests indicate that the cement paste containing montmorillonite are denser than that of the plain cement paste. X-ray diffraction analysis showed that the main hydration products are portlandite, hatrurite and calcite in cement paste and quartz and portlandite in cement mortar.
6 April 2016 in Science and Engineering of Composite Materials
The study investigates the effects of the alkaline solution/binder ratio and the curing condition on the mechanical properties of alkali-activated fly ash (AAFA) mortars. Class F fly ash was used as the raw material, and sodium hydroxide and liquid sodium silicate were used for the preparation of alkaline activators. Three alkaline solution-to-binder ratios (0.35, 0.5, and 0.65) and four different initial curing conditions (curing in air at ambient temperature for 24 h, 30°C for 24 h, 65°C for 12 h, and 85°C for 6 h) were considered. Test results show that AAFA mortars with alkaline solution-to-binder ratio of 0.35 had higher compressive strength, lower drying shrinkage, lower water absorption, and lower initial surface absorption rate than the other mortars. Furthermore, the curing condition influenced the compressive strength development and drying shrinkage of AAFA mortars at early ages. AAFA mortars cured at 65°C for 12 h appeared to have superior mechanical properties. XRD demonstrates that the hydration products of AAFA mortars are mainly amorphous alkaline aluminosilicate gel, which attributed to the compressive strength. Consequently, the alkaline solution-to-binder ratio significantly affects more the mechanical properties than the curing condition based on the presented results.
This study investigates the effectiveness of concrete protection with two inorganic silicate sealer materials (ISSMs). The Taguchi method and grey relational analysis (GRA) have been used to identify the key factors influencing concrete protection provided by the surface treatment. Seven control factors with two levels were selected. By using the orthogonal array L12 (27), 12 experiments are chosen and four tests—the compressive strength test, resistivity test, absorption test and permeability test—were performed. Results have shown that the major factors affecting the protection effectiveness of ISSM are the water-binder ratio of mortar substrate, age of substrate for sealer application, addition of pozzolanic material and sealer type.
1 June 2012 in Science and Engineering of Composite Materials
The influence of water/cementitious material ratio, silica fume, and fly ash as partial Portland cement replacement materials on the properties, pore structure, and durability of cement-based composites was evaluated by conducting compressive strength test, mercury intrusion porosimetry test, water absorption, rapid chloride penetration test, and scanning electron microscopy (SEM). Water/cementitious material ratio, and replacement percentage of silica fume and fly ash have significant effects on the pore structure and durability of cement-based composites. Composites with silica fume or fly ash have a denser structure than the control composite on SEM micrographs. Silica fume has about 5–10 times as much effect as fly ash, according to results of multiple linear regression analyses of testing data.