The aim of this study is to provide better insights into the cerebral perfusion patterns and collateral mechanism of the circle of Willis (CoW) under anatomical and pathological variations. In the current study, a patient-specific three-dimensional computational model of the CoW was reconstructed based on the computed tomography (CT) images. The Carreau model was applied to simulate the non-Newtonian property of blood. Flow distributions in five common anatomical variations coexisting with different degrees of stenosis in the right internal carotid artery (RICA) were investigated to obtain detailed flow information. With the development of stenosis in unilateral internal carotid artery (ICA), the cerebral blood supply decreased when the degree of stenosis increased. The blood supply of the ipsilateral middle cerebral artery (MCA) was most affected by the stenosis of ICA. The anterior communicating artery (ACoA) and ipsilateral posterior communicating artery (PCoA) functioned as the important collateral circulation channels when unilateral stenosis occurred. The blood flow of the anterior circulation and the total cerebral blood flow (CBF) reached to the minimum in the configuration of the contralateral proximal anterior cerebral artery (A1) absence coexisting with unilateral ICA stenosis. Communicating arteries provided important collateral channels in the complete CoW when stenosis in unilateral ICA occurred. The cross-flow in the ACoA is a sensitive indicator of the morphological change of the ICA. The collateral function of the PCoA on the affected side will not be fully activated until a severe stenosis occurred in unilateral ICA. The absence of unilateral A1 coexisting with the stenosis in the contralateral ICA could be the most dangerous configuration in terms of the total cerebral blood supply. The findings of this study would enhance the understanding of the collateral mechanism of the CoW under different anatomical variations.
The Circle of Willis (CoW) is an important collateral pathway of the cerebral blood flow. An experimental study of the cerebral blood flow (CBF) distribution in different anatomical variations may help to a better understanding of the collateral mechanism of the CoW. An in-vitro test rig was developed to simulate the physiological cerebral blood flow in the CoW. Ten anatomical variations were considered in this study, include a set of different degrees of stenosis in L-ICA and L-ICA occlusion coexist with common anatomical variations. Volume flow rates of efferent arteries and pressure signals at the end of communicating arteries of each case were recorded. Physiological pressure waveforms were applied as inlet boundary condition. In the development of L-ICA stenosis, the total CBF decreases with the increase of stenosis degree. The blood supply of ipsilateral middle cerebral artery (MCA) was affected most by the stenosis of L-ICA. Anterior communicating artery (ACoA) and ipsilateral posterior communicating artery (PCoA) function as important collateral pathways of cerebral collateral circulation when unilateral stenosis occurred. The blood supply of anterior cerebral circulation was compensated by the posterior cerebral circulation through ipsilateral PCoA when L-ICA stenosis degree is greater than 40% and the affected side was compensated immediately by the unaffected side through ACoA. Blood flow of the anterior circulation and the total CBF reached the minimum among all cases studied when L-ICA occlusion coexist with the absence of PCoA. The results demonstrated the flow distribution patterns of the CoW under anatomical variations and clarified the collateral mechanism of the CoW. The flow ACoA is the most sensitive indexes to the morphology change of ipsilateral ICA. The relative independence of the circulation in anterior and posterior sections of the CoW is not broken and the function of ipsilateral PCoA is not activated until a severe stenosis of unilateral ICA occurs. PCoA is the most important collateral pathway of the collateral circulation and the missing of PCoA has the highest risk of stroke when the ipsilateral ICA has severe stenosis. These findings may provide the basis for future therapeutic and diagnosis applications.
22 August 2012 in Journal of Engineering for Gas Turbines and Power
The rod-fastened rotor (RFR) is comprised of a series of discs clamped together by a central tie rod or several tie rods on the pitch circle diameter. The equivalent flexural stiffness of contact interfaces Kc in the RFR is the key concern for accurate rotor dynamic performance analysis. Each contact interface was modeled as a bending spring with a stiffness of Kc and a hinge in this study. The contact states of the contact interfaces, which depend on the pretightening forces and bending moments (static), have effects on Kc. The approach to calculating Kc in two contact states is presented. The first contact state is that the whole zone of the contact interface is in contact; Kc is determined by the contact layer, which consists of asperities of the contact surfaces. Hertz contact theory and the Greenwood and Williamson (GW) statistical model are used to calculate the equivalent flexural stiffness of the contact layer Kcc. The second contact state is that some zones of the contact interface are separated (when the bending moment is relatively large); the equivalent flexural stiffness of the rotor segment Ksf (not including Kcc) decreases, as the material in the separated zone has no contribution to the bending load-carrying capacity of the rotor. The strain energy, which is calculated by the finite element method (FEM), is used to determine Ksf. The stiffness Ksf is equivalent to the series stiffness of the discs of the rotor segment with flexural stiffness of Kd and a spring with bending stiffness of Kcf in the location of the contact interface, so Kc is equal to the series stiffness of Kcc and Kcf in the second contact state. The results of a simplified RFR indicate that, for a fixed pretightening force, Kcc decreases with bending moments in the first contact state, whereas increases with bending moments in the second contact state. In addition, Kcf and Kc decrease abruptly with the increase of bending moments in the second contact state when the rotor is subjected to a relatively large pretightening force. Finally, the multipoint exciting method was used to measure the modal parameters of the experimental RFR. It is found that the experimental modal frequencies decrease as the pretightening force decreases.
15 January 2014 in Journal of Vibration and Acoustics
Rod-fastened rotors are composed of some disks clamped together by a central tie rod or several tie rods distributed along the circumference. Due to the nonlinear flexural stiffness of the contact interfaces in disks, especially when the contact surfaces are partially separated, the dynamics of the rod-fastened rotors are potentially different from that of the solid rotors. In this paper, the nonlinear flexural stiffness of a rod-fastened Jeffcott rotor is calculated by the finite element method (FEM). Then the harmonic balance method is adopted to analyze the dynamics of the rotor. The flexural stiffness of a rod-fastened Jeffcott rotor dramatically decreased with the increase of the dimensionless load γ1 from 1 to 2.5. Thus, the dynamics of the rotor were nonlinear when it was subjected to a large unbalance force. The response of the rotating rotor contains a predominantly forward 1X component or both forward 1X component and backward 1X components. However, the rotor may settle in a state depending upon both the operating parameters and its history.
As a competitive small-scale turbomachinery option, Tesla turbines have wide potential in various fields, such as renewable energy generation systems and small power equipment. This paper investigates the influence of disc tip geometry, including its profile and relative height, on the aerodynamic performance and flow characteristics of one-to-one and one-to-many multichannel Tesla turbines. The results indicate that compared to the turbine with blunt tips, the isentropic efficiency of the one-to-one turbine with sharp tips has a little decrease, which is because the relative tangential velocity gradient near the rotational disc walls decreases a little and additional vortices are generated at the rotor inlet, while that of the one-to-many turbine with sharp tips increases significantly, resulting from an increase in the relative tangential velocity in the disc channels and a decrease in the low Mach number and vortex area; for instance the turbine efficiency for the former relatively decreases by 3.6% and that for the latter increases by 13.5% at 30,000 r/min. In addition, the isentropic efficiency of the one-to-many turbine with sharp tips goes up with increasing relative height due to increasing improvement of flow status, and its increment rate slows down. A circular or elliptic tip performs better with lower relative height and a triangular tip behaves better with higher relative height. To sum up, a blunt disc tip is recommended for the one-to-one turbine, and a sharp disc tip is for the one-to-many turbine. The relative height and tip profile of the one-to-many turbine should be determined according to their effects on turbine performance, manufacturing difficulty and mechanical deformation.
Tesla turbines are a kind of unconventional bladeless turbines, which utilize the viscosity of working fluid to rotate the rotor and realize energy conversion. They offer an attractive substitution for small and micro conventional bladed turbines due to two major advantages. In this study, the effects of two influential geometrical parameters, disc thickness and disc spacing distance, on the aerodynamic performance and flow characteristics for two kinds of multichannel Tesla turbines (one-to-one turbine and one-to-many turbine) were investigated and analyzed numerically. The results show that, with increasing disc thickness, the isentropic efficiency of the one-to-one turbine decreases a little and that of the one-to-many turbine reduces significantly. For example, for turbine cases with 0.5 mm disc spacing distance, the former drops less than 7% and the latter decreases by about 45% of their original values as disc thickness increases from 1 mm to 2 mm. With increasing disc spacing distance, the isentropic efficiency of both kinds of turbines increases first and then decreases, and an optimal value and a high efficiency range exist to make the isentropic efficiency reach its maximum and maintain at a high level, respectively. The optimal disc spacing distance for the one-to-one turbine is less than that for the one-to-many turbine (0.5 mm and 1 mm, respectively, for turbine cases with disc thickness of 1 mm). To sum up, for designing a multichannel Tesla turbine, the disc spacing distance should be among its high efficiency range, and the determination of disc thickness should be balanced between its impacts on the aerodynamic performance and mechanical stress.