As a competitive small-scale turbomachinery option, Tesla turbines have wide potential in various fields, such as renewable energy generation systems and small power equipment. This paper investigates the influence of disc tip geometry, including its profile and relative height, on the aerodynamic performance and flow characteristics of one-to-one and one-to-many multichannel Tesla turbines. The results indicate that compared to the turbine with blunt tips, the isentropic efficiency of the one-to-one turbine with sharp tips has a little decrease, which is because the relative tangential velocity gradient near the rotational disc walls decreases a little and additional vortices are generated at the rotor inlet, while that of the one-to-many turbine with sharp tips increases significantly, resulting from an increase in the relative tangential velocity in the disc channels and a decrease in the low Mach number and vortex area; for instance the turbine efficiency for the former relatively decreases by 3.6% and that for the latter increases by 13.5% at 30,000 r/min. In addition, the isentropic efficiency of the one-to-many turbine with sharp tips goes up with increasing relative height due to increasing improvement of flow status, and its increment rate slows down. A circular or elliptic tip performs better with lower relative height and a triangular tip behaves better with higher relative height. To sum up, a blunt disc tip is recommended for the one-to-one turbine, and a sharp disc tip is for the one-to-many turbine. The relative height and tip profile of the one-to-many turbine should be determined according to their effects on turbine performance, manufacturing difficulty and mechanical deformation.
Tesla turbines are a kind of unconventional bladeless turbines, which utilize the viscosity of working fluid to rotate the rotor and realize energy conversion. They offer an attractive substitution for small and micro conventional bladed turbines due to two major advantages. In this study, the effects of two influential geometrical parameters, disc thickness and disc spacing distance, on the aerodynamic performance and flow characteristics for two kinds of multichannel Tesla turbines (one-to-one turbine and one-to-many turbine) were investigated and analyzed numerically. The results show that, with increasing disc thickness, the isentropic efficiency of the one-to-one turbine decreases a little and that of the one-to-many turbine reduces significantly. For example, for turbine cases with 0.5 mm disc spacing distance, the former drops less than 7% and the latter decreases by about 45% of their original values as disc thickness increases from 1 mm to 2 mm. With increasing disc spacing distance, the isentropic efficiency of both kinds of turbines increases first and then decreases, and an optimal value and a high efficiency range exist to make the isentropic efficiency reach its maximum and maintain at a high level, respectively. The optimal disc spacing distance for the one-to-one turbine is less than that for the one-to-many turbine (0.5 mm and 1 mm, respectively, for turbine cases with disc thickness of 1 mm). To sum up, for designing a multichannel Tesla turbine, the disc spacing distance should be among its high efficiency range, and the determination of disc thickness should be balanced between its impacts on the aerodynamic performance and mechanical stress.
28 December 2022 in International Communications in Heat and Mass Transfer
This paper numerically studies the effect of a V-shaped protrusion vortex generator on flow and heat transfer of impingement cooling in crossflow. The simulations are performed by solving three-dimensional steady Reynolds-Averaged Navier-Stokes equations with shear stress transport k-Omga turbulence model. Four crossflow ratios, five locations and heights of the V-shaped protrusion vortex generator are discussed. Results indicate that (1) the V-shaped protrusion vortex generator effectively improves the peak value of Nusselt number and widens the high heat transfer range at the crossflow ratios of 0.3 and 0.4 due to the decrease of actual crossflow ratio and the generation of an additional counter-rotating vortex pair, while it has little effect at the crossflow ratios of 0.1 and 0.2; (2) as the distance between vortex generator and jet hole increases from 2.5 to 4.5 times of diameter, the Nusselt number increases and the jet total pressure drop decreases, thus the thermal performance factor increases with a maximum increasement of 22.57%; and (3) the Nusselt number increases with the increase of vortex generator height, and when the crossflow ratio is large enough, the impingement heat transfer can be improved even that a shallow V-shaped protruding vortex generator is used.