Significance: There has been an intense search for the ideal light sources for high-speed, full-field imaging applications ranging from next-generation microscopes and laser projectors to digital holography and photolithography. Traditional lasers, although providing the required brightness (i.e., power per mode), exhibit high spatial coherence, which introduces coherent artifacts such as speckle, corrupting image formation. At the other extreme, low spatial coherence sources such as thermal sources and light emitting diodes (LEDs) avoid speckle but lack sufficient power per mode for high-speed imaging. In this work, we demonstrate a new type of semiconductor laser based on a chaotic cavity, which combines low spatial coherence with high power per mode. Such a laser could enable a wide range of full-field imaging applications.

We present a low-noise distributed acoustic sensor using enhanced backscattering fiber with a series of localized reflectors. The point reflectors were inscribed in a standard telecom fiber in a fully automated system by focusing an ultra-fast laser through the fiber cladding. The inscribed reflectors provided a reflectance of −53 dB, significantly higher than the Rayleigh backscattering level of −70 dB/m, despite adding only 0.01 dB of loss per 100 reflection points. We constructed a coherent φ-OTDR system using a double-pulse architecture to probe the enhanced backscattering fiber. Using this system, we found that the point reflectors enabled an average phase noise of −91 dB (re rad²/Hz), 20 dB lower than sensors formed using Rayleigh backscattering in the same fiber. The sensors are immune to interference fading, exhibit a high degree of linearity, and demonstrate excellent non-local signal suppression (>50 dB). This work illustrates the potential for low-cost enhanced backscattering fiber to enable low-noise, long-range distributed acoustic sensing.

Characterizing ultrashort optical pulses has always been a critical but difficult task, which has a broad range of applications. We propose and demonstrate a self-referenced method of characterizing ultrafast pulses with a multimode fiber. The linear and nonlinear speckle patterns formed at the distal end of a multimode fiber are used to recover the spectral amplitude and phase of an unknown pulse. We deploy a deep learning algorithm for phase recovery. The diversity of spatial and spectral modes in a multimode fiber removes any ambiguity in the sign of the recovered spectral phase. Our technique allows for single-shot pulse characterization in a simple experimental setup. This work reveals the potential of multimode fibers as a versatile and multi-functional platform for optical sensing.

Brillouin fiber sensors can provide distributed strain and temperature measurements over long distances in standard off-the-shelf fiber by measuring the Brillouin frequency shift as a function of position along a fiber. The primary drawback of these systems is their limited sensitivity, which results from the challenge in identifying the Brillouin frequency shift to within a small fraction of the Brillouin linewidth. In this work, we introduce a technique that overcomes this fundamental limitation by establishing a series of lasing modes that experience Brillouin amplification at discrete spatial locations in the test fiber. The linewidth narrowing and high intensity associated with the lasing transition enable precise measurements of this lasing frequency. As an initial demonstration, we present a sensor that simultaneously excites 40 lasing modes in a 400 m fiber, providing a measurement of the strain at 40 discrete locations with a spatial resolution of 4 m. Each sensor exhibits a minimum detectable strain as low as 4 n ε / H z 1 / 2 with a dynamic range of > 5 m ε and a bandwidth of ∼ 10 k H z . As the first demonstration that Brillouin lasing can be used for distributed fiber sensing, this work establishes an approach that could enable ultrahigh strain sensitivity using off-the-shelf fiber.

Optical frequency comb sources provide thousands of precise and accurate optical lines in a single device enabling the broadband and high-speed detection required in many applications. A main challenge is to parallelize the detection over the widest possible band while bringing the resolution to the single comb-line level. Here we propose a solution based on the combination of a frequency comb source and a fibre spectrometer, exploiting all-fibre technology. Our system allows for simultaneous measurement of 500 isolated comb lines over a span of 0.12 THz in a single acquisition; arbitrarily larger span are demonstrated (3,500 comb lines over 0.85 THz) by doing sequential acquisitions. The potential for precision measurements is proved by spectroscopy of acetylene at 1.53 μm. Being based on all-fibre technology, our system is inherently low-cost, lightweight and may lead to the development of a new class of broadband high-resolution spectrometers.

The diversity of spatial modes present within a multimode fiber has been exploited for a wide variety of imaging and sensing applications. Here, we show that this diversity of modes can also be used to perform quantitative strain sensing by measuring the amplitude of the Rayleigh backscattered speckle pattern in a multimode fiber. While most Rayleigh based fiber sensors use single mode fiber, multimode fiber has the potential to provide lower noise due to the higher capture fraction of Rayleigh scattered light, higher non-linear thresholds, and the ability to avoid signal fading by measuring many spatial modes simultaneously. Moreover, while amplitude measuring single mode fiber based Rayleigh sensors cannot provide quantitative strain information, the backscattered speckle pattern formed in a multimode fiber contains enough information to extract a linear strain response. Here, we show that by tracking the evolution of the backscattered speckle pattern, the sensor provides a linear strain response and is immune to signal fading. The sensor has a noise floor of 2.9 pɛ/√Hz, a dynamic range of 74 dB at 1 kHz, and bandwidth of 20 kHz. This work paves the way for a new class of fiber optic sensors with a simplified design and enhanced performance.