Hole concentration of 2-D hole gas (2DHG) on (110) diamond is higher than that on other faces, making it the best choice for power device application. Detailed analysis of atomic layer deposition (ALD) Al 2 O 3 /(110) C–H diamond interface structure is of vital importance. MOSFETs with thin (10 nm) and thick (100 nm) ALD Al 2 O 3 layer were made in this study. The microstructure of Al 2 O 3 on (110) C–H diamond was analyzed. Abrupt interface of ALD Al 2 O 3 /C–H diamond was observed through high resolution transmission electron microscope (HRTEM). Cascode structure using diamond MOSFETs and enhancement mode silicon MOSFET is fabricated and its high performance is confirmed.
12 July 2022 in IEEE Transactions on Electron Devices
A novel method to fabricate the oxidized silicon-terminated (C–Si–O) diamond metal-oxide-semi- conductor field-effect transistors (MOSFETs) by replacing the retained SiO 2 masks with an atomic layer deposition (ALD)-Al 2 O 3 film as the main gate insulator was proposed for the first time. Compositional analysis across the SiO 2 masks and on the air-exposed C–Si–O (111) diamond surface has been carried out by utilizing secondary ion mass spectroscopy (SIMS) and Auger electron spectroscopy (AES) techniques, respectively. Furthermore, we revealed that, under selectively epitaxial growth of diamond through a SiO 2 mask, a carbon-rich film was formed on SiO 2 and C–Si bonding was realized at the SiO 2 /(111) diamond interface. The fabricated device with a source and drain distance ( ${L}_{SD}$ ) of $3 \,\mu \text{m}$ exhibits a distinct threshold voltage ( ${V}_{TH}$ ) of −5.6 V and a maximum drain current density ( ${I}_{D\_{}{MAX}}$ ) up to −311 mA/mm, which is a record value among normally-off single-crystalline diamond MOSFETs to date. In the case of having ALD-Al 2 O 3 as the main gate insulator, normally-off operation of the C–Si–O diamond MOSFETs has a stark contrast with the typically normally-on performance of the hydrogen-terminated (C–H) diamond MOSFETs, which is mainly due to the smaller negative electron affinity of C–Si–O diamond compared with that of C–H diamond. These results indicate that the proposed C–Si–O (111) diamond MOSFETs with excellent normally-off operation and large drain current density are promising to fulfill the requirements of fail-safe and current drive capabilities in power device applications.
23 March 2022 in IEEE Transactions on Electron Devices
In this article, the normally- OFF oxidized Si-terminated (C–Si) diamond metal–oxide–semiconductor field-effect transistors (MOSFETs) with as-deposited 0.5-nm silicon on diamond annealed at high temperature as the subsurface p-channel were presented for the first time. A novel method utilizing both a metal mask to realize the regrown heavily boron-doped (001) diamond layer first (p + -diamond-first) and a molecular beam deposition (MBD) method to procure atomic-scale silicon deposition was achieved. Scanning transmission electron microscopy (STEM) and energy-dispersive X-ray spectroscopy (EDS) element mapping results suggest that the C–Si diamond/Al 2 O 3 interface is quite continuous and atomically flat. A remarkably high threshold voltage ( ${V}_{\text{TH}}$ ) of −10 V and a maximum drain current density ( ${I}_{D\_{}{\text{MAX}}}$ ) of −156 mA/mm are simultaneously achieved in the fabricated devices. The devices with different source and drain (S/D) distances ( $L_{\text{SD}}$ ) deliver robust ${V}_{\text{TH}}$ results and feature low OFF-state S/D leakage current $\vert {I}_{\text{leakage}}\vert $ of ~ $6\times10$ −6 mA/mm at ${V}_{\text{GS}}$ = 0 V. The extracted field-effect mobility is as high as 127 cm 2$\cdot \text{V}$ −1$\cdot \text{s}$ −1 and the interface state density is as low as $4.35\times10$ 12 eV −1$\cdot $ cm −2 . These competitive results reveal that this first attempt of employing the combination of p + -diamond-first and MBD approaches promotes the integration of the advanced silicon manufacturing process with wide bandgap diamond material for power applications.
The mechanism of hydrogen-terminated (H-terminated) single-crystal and polycrystalline diamond metal–oxide field-effect transistors (MOSFETs) is investigated in this letter. In order to characterize the complicated p-type surface layer in H-terminated diamond MOSFETs, both p-type acceptors and the C–H dipole effect are considered in our model. Simulated hole distribution and band bending are used to illustrate the operation mechanism in the surface region. Simulated results by using the proposed model match well with both measured ${I} - {V}$ and transfer characteristics of these two kinds of diamond MOSFETs. Moreover, channel lattice temperature distribution reveals that self-heating effect-induced slight current collapse occurs in the polycrystalline diamond MOSFET at ${I}_{\text {ds}} $ over 500 mA/mm due to relatively lower thermal conductivity. Finally, the lateral electric field and hole velocity distribution under the gate electrode are given to aid future research.
With a dense two-dimensional hole gas (2DHG) p-type conductive layer near the surface, hydrogen-terminated (C–H) diamond metal-oxide-semiconductor field-effect transistors (MOSFETs) have shown typical normally-on operations and high breakdown voltages ( V BR ). Owing to the high MOS interface quality, the oxidized silicon-terminated (C–Si–O) diamond MOSFETs have featured excellent normally-off characteristics, such as high threshold voltage ( V TH ). However, the reported C–Si–O diamond MOSFETs were all exhibited an overlapping-gate structure, and therefore couldn’t withstand high voltages. In this work, we demonstrated a novel C–H diamond MOSFET structure with a partial C–Si–O channel to improve the voltage withstand capability of normally-off C–Si–O diamond MOSFETs. The C–H/C–Si–O/C–H channel structure was achieved by forming an entire C–Si–O channel first, and then selectively replacing the C–Si–O channel to the C–H channel by using a SiO 2 mask. As a result, for the fabricated device with a C–Si–O channel length of 2 μm and a gate-to-drain distance ( L GD ) of 11 μm, V TH = -8.6 V and OFF-state V BR = -1376 V have been obtained. These competitive results reveal that the proposed device structure is promising in pushing the normally-off C–Si–O diamond MOSFETs into the high voltage applications.
A compact large-signal model for hydrogen-terminated (C-H) diamond metal-oxide field effect transistors (MOSFETs) is presented based on an improved quasi-physical zone division (QPZD) model. Unlike the conventional QPZD model for the AlGaN/GaN high-electron mobility transistors (HEMTs), the linear-mode current-voltage (I-V) model of the diamond FET is analytically deduced with an improved velocity-electric field relation and temperature-dependent effective hole mobility μeff(T). The I-V model can directly demonstrate the relation between the negative Vds and the negative Ids of the p-type diamond FETs, which cannot be achieved by the conventional QPZD model. Finally, the proposed model has been verified by the on-wafer measurements of an in-house 2 × 500 μm diamond FET. The good consistency shows that the presented compact large-signal model can accurately predict the DC I-V, multibias scattering-parameters (S-parameters), and large-signal performances. The results of this paper will be useful for the microwave diamond-based transistor and circuit designs.