Hole concentration of 2-D hole gas (2DHG) on (110) diamond is higher than that on other faces, making it the best choice for power device application. Detailed analysis of atomic layer deposition (ALD) Al 2 O 3 /(110) C–H diamond interface structure is of vital importance. MOSFETs with thin (10 nm) and thick (100 nm) ALD Al 2 O 3 layer were made in this study. The microstructure of Al 2 O 3 on (110) C–H diamond was analyzed. Abrupt interface of ALD Al 2 O 3 /C–H diamond was observed through high resolution transmission electron microscope (HRTEM). Cascode structure using diamond MOSFETs and enhancement mode silicon MOSFET is fabricated and its high performance is confirmed.
Heat dissipation significantly limits semiconductor component performance improvement. Thermal management devices are pivotal for electronic chip heat dissipation, with the enhanced thermal conductivity of materials being crucial for their effectiveness. This study focuses on single-crystal diamond, renowned for its exceptional natural thermal conductivity, investigating diamond microchannels using finite element simulations. Initially, a validated mathematical model for microchannel flow heat transfer was established. Subsequently, the heat dissipation performance of typical microchannel materials was analyzed, highlighting the diamond’s impact. This study also explores diamond microchannel topologies under high-power conditions, revealing unmatched advantages in ultra-high heat flux density dissipation. At 800 W/cm2 and inlet flow rates of 0.4–1 m/s, diamond microchannels exhibit lower maximum temperatures compared to pure copper microchannels by 7.0, 7.2, 7.4, and 7.5 °C, respectively. Rectangular cross-section microchannels demonstrate superior heat dissipation, considering diamond processing costs. The exploration of angular structures with varying parameters shows significant temperature reductions with increasing complexity, such as a 2.4 °C drop at i = 4. The analysis of shape parameter ki indicates optimal heat dissipation performance at ki = 1.1. This research offers crucial insights for developing and optimizing diamond microchannel devices under ultra-high-heat-flux-density conditions, guiding future advancements in thermal management technology.
A thickness asymmetric electrode structure on an oxygen-terminated type IIa diamond was designed and prepared (one electrode was semitransparent to ultraviolet light and the other blocked the transmission of ultraviolet light). This structure exhibited an apparent photo-induced rectification property under irradiation by a deuterium lamp. This is attributed to the mechanism by which the light penetrating the electrode reduces the metal–diamond contact barrier. Furthermore, we developed a light-modulated Schottky barrier diamond photodetector based on this mechanism. Solar-blind light can lower the Schottky barrier height in situ in the presence of light, which significantly enhances the photocurrent. However, the Schottky barrier is not reduced by light regulation when there is no light; therefore, the low dark current of the detector is still guaranteed. Compared with the non-photo-regulated Schottky barrier detector, the photo-regulated Schottky barrier detector exhibits a 128% increase in responsivity at 220 nm under a 1.6 V/μm bias. For such an obvious difference in detection performance, this mechanism has rarely been a focus of studies on diamond detectors. In addition to diamond detectors, light-modulated barrier technology can also be applied to other fields related to the diamond surface potential, such as color center control and Schottky diodes; it can also be used to control or evaluate device performance.
Temperature monitoring is considerably important during the operation of power devices. Herein, pseudo-vertical diamond Schottky diodes with a low doped drift layer were fabricated as diode temperature sensors. The current–voltage characteristics determined in the range of 298–664 K revealed an increase in the forward current with increasing temperature. The sensing ability of the as-fabricated sensors was evaluated by characterizing the temperature dependence of the forward voltage drop at certain currents. In this study, the highest sensitivity was obtained for a diode temperature sensor based on the wide-bandgap semiconductor. However, the obtained sensitivities exhibited different values in high and low temperature ranges for the currents of 10 -5 , 10 -4 and 10 -3 A. To explain the sectional sensitivities, theoretical models were proposed based on the thermionic emission model and Cheung's model. The results indicated the presence of an inhomogeneous Schottky contact and a temperature-dependent series resistance, which explained the sectional and ultrahigh sensitivities.
For the first time, robust ohmic contacts were successfully prepared on oxygen-terminated intrinsic diamond with insulating surface and rare carrier concentration by transition metals (TMs, including Pt, Ru, W, Cr, Zr and V) metallization. The record low specific contact resistance of ${2}.{5}\times {10} ^{-{8}}~\Omega $ cm2 was obtained for Pt contacts, which diffused into diamond in a metallic state and did not generate carbide but sp2 carbon and vacancy defects. We found that the shallow damage layer full of conductive defects like TMs, TM carbides, sp2 carbon and nitrogen-vacancy color centers induced by metallization within diamond is the critical reason for the formation of ohmic contacts, which acts as conductive shunts to connect the electrode contact and bulk diamond. Our findings extended the methodology and theory for the formation of reliable and efficient ohmic contacts on diamond.