In metal cutting processing, especially in the processing of low-rigidity workpieces, chatter is a crucial factor affecting many aspects such as surface quality, processing efficiency, and tool life. In this paper, a novel online chatter detection method for milling processes is proposed. In this method, firstly, periodic signal and noise parts are filtered by a comb filter and empirical mode decomposition (EMD), respectively. Then, signal reconstruction is performed on the intrinsic mode functions (IMFs) based on the Pearson correlation coefficient. GWO is applied to reconstruct the signal to obtain optimized parameters. Subsequently, the reconstructed signal is decomposed by VMD with the optimal parameters. To obtain rich chatter information frequency bands, the energy entropy characteristics of each order IMF are calculated, and the two-order IMFs with larger energy entropy are selected for reconstruction. Finally, the multi-scale permutation entropy (MPE) and multi-scale fuzzy entropy (MFE) of the reconstructed signal are calculated. According to the value range of entropy in each processing state, the optimal scale feature is selected. The analysis results show that the proposed method can effectively detect the milling processing state based on the optimal scale.
24 June 2021 in Journal of Vibration Engineering & Technologies
Magnetic levitation rotating machinery has been widely used in industrial applications. Odd harmonic currents in the active magnetic bearing coils, which are caused by rotor mass unbalance and sensor runout, increase the power consumption and the base vibration. Repetitive control has recently been used to suppress harmonic currents in magnetic bearing systems. However, repetitive control needs the rotor rotational speed information and has some limitations without a speed sensor. In this paper, an adaptive odd repetitive control which does not need the speed sensors is proposed to suppress the active magnetic bearing odd harmonic currents. Compared to the conventional repetitive control, the second-order generalized integral frequency-locked loop is applied in adaptive odd repetitive control to estimate the rotor speed in real time without additional speed sensors. The magnetically suspended rotor with harmonic disturbances is modeled. The work principle, structure, and design of the adaptive odd repetitive control are addressed. The simulation and experiments are carried out on a rotor active magnetic bearing test rig to validate the effectiveness of the proposed adaptive odd repetitive control, and the results show that the active magnetic bearing odd harmonic currents are well suppressed.
Rotor-Active magnetic bearing (rotor-AMB) systems offer significant advantages in power consumption and are increasingly being applied in fluid machinery. However, in such machinery, the impeller and the rotor are commonly connected by bolt fastening. Once a certain pre-tightening force is applied to the bolted connection and the interface contact between the rotor and the impeller is formed, the flexible modal vibration will be excited when the rotor is levitated. The conventional Proportional-Integral-Derivative (PID) controller is limited in this vibration suppression and it is essential to increase the damping at bending mode to inhibit vibration. However, the calculation of the optimal phase compensated is based on the rotor-AMB model considering interface contact. In this work, the effect of the interface contact is equivalent to massless spring units, and the disturbance generated by spring units is acted upon the mechatronic system in the way of positive feedback. The detailed description of the transfer function from the disturbance to rotor deformation at fourth bending mode is obtained by theoretical model and system identification. The optimal phase of the system needed to inhibit the disturbance is determined by minimizing the gain of the transfer function at fourth bending mode. A combination of PID control and phase compensation is implemented in the experiment. The results show that the optimal phase is 50° as the calculation and the optimal phase compensation control can sufficiently inhibit the modal vibration.
Featured with optimal power consumption, active magnetic bearings (AMBs) have been extensively integrated into turbomachinery applications. For turbomachinery components, including the rotor and impeller, their connection is generally based on bolted joints, which would easily induce excessive interface contact. As a result, the pre-tightening torque can induce modal vibrations in the rotor upon levitation. Although a notch filter can be adopted to suppress the vibrations, it should be noted that the current reported notch filters are based on fixed center frequency, making it challenging to enable high effectiveness over a broad range of rotor speeds, particularly in cases where the gyroscopic effect is significant. Herein, a modal vibration suppression based on a varying-frequency notch filter is proposed, considering gyroscopic effect and interface contact. First, the rotor–AMB system was developed, taking into consideration the bolted-joint interface contact. This modeled the effect of the interface contact as a time-varying force in the positive feedback. Secondly, the relationship between vibration frequency and rotational speed was obtained, based on simulations. Lastly, a test rig was configured to validate the performance of the frequency-varying notch filter. The experimental data confirm that the filter is capable of attenuating the modal vibrations resulting from interface contact across all operational speeds.