The injection of carbon dioxide (CO2) is an essential technology for maximizing the potential of hydrocarbon reservoirs while reducing the impact of greenhouse gases. However, because of the complexity of this injection, there will be many different chemical reactions between the formation fluids and the rock minerals. This is related to the clay content of sandstone reservoirs, which are key storage targets. Clay content and clay types in sandstone can vary substantially, and the influence of these factors on reservoir-scale CO2-water-sandstone interactions has not been managed appropriately. Consequently, by simulating the process of CO2 injection in two different clay-content sandstones (i.e., high- and low-clay content), we investigated the effect of the sandstone clay concentration on CO2-water-sandstone interactions in this article. High clay content (Bandera Grey sandstone) and low clay content (Bandera Brown sandstone) were considered as potential storage reservoirs and their responses to CO2 injection were computationally assessed. Our results indicate that the mineralogical composition of the sandstone reservoir significantly varies as a result of CO2-water-sandstone interactions. Clearly, the high clay-content sandstone (Bandera Grey) had a higher maximum CO2 mineral-trapping capacity (6 kg CO2/m3 sandstone) than Bandera Brown Sandstone (low clay content), which had only 3.3 kg CO2/m3 sandstone mineral-storage capacity after 400 years of storage. Interestingly, pH was decreased by ~3 in Bandera Grey sandstone and by ~2.5 in Bandera Brown sandstone. Furthermore, porosity increased in Bandera Grey sandstone (by +5.6%), more than in Bandera Brown Sandstone (+4.4%) after a 400-year storage period. Overall, we concluded that high clay-content sandstone shows more potential for CO2 mineral-trapping.
8 April 2023 in Iraqi Journal of Oil and Gas Research (IJOGR)
The state of the economy today highlights the requirement for better engineering designs in drilling, well completion, and reservoir production processes. Continuous profiles of rock mechanical properties are required for all of the aforementioned activities. Elastic and strength parameters are two categories that can be used to categorize rock mechanical parameters. Elastic parameters that describe the behavior and tendency of rock to fluctuation or fracture under stress include Young's modulus, bulk module, shear modulus, and Poisson's ratio. To prevent various drilling issues including well kicks pipe sticking, and wellbore instability, it is crucial to understand the elastic properties of reservoir rock. It is therefore conceivable to have an accurate estimation of the rock elastic behavior. The various techniques for estimating the various elastic properties are reviewed in this work. Both a static and dynamic calculation can be done for elastic characteristics. When employing static methods, the elastic modulus can be calculated by measuring it on real cores in a lab using pricy procedures. Whereas well logs are utilized in dynamic methods, a quicker and less expensive technique, to calculate the parameters governing rock elastic properties.
Lost circulation is a major issue that increases the cost of petroleum exploration operations. During the well planning period, consideration of the degree of severity of mud loss may lead to significant technical and financial benefits. This will assist in the prevention of losses by putting preventative measures in place before running into lost circulation region. This study aimed to predict the amount of mud loss rate (MLR) by using new models with artificial neural networks (ANNs). This model was built in order to obtain a knowledge of the relationship between the amount of loss and the drilling parameters that can be controlled, such as (the rate of penetration (ROP), flow rate (FLW), standpipe pressure (SPP), weight on bit (WOB), nozzle area (TFA), rotation per minute (RPM), and torque (TRQ)), the drilling fluid properties and geomechanical properties like unconfined compressive strength (UCS). Gaining information about UCS along the wellbore is essential for dealing with drilling problems like lost circulation. The new model was developed using a dataset of 209 loss events that were collected from 21 oil wells in the Rumaila oil field’s Dammam and Hartha formations that encountered loss circulation events. Apart from other controllable drilling parameters, it was demonstrated that the rate of losses was also sensitive to UCS values. The amount of mud losses rate constantly rises with increasing UCS. The suggested artificial neural networks (ANN) model was employed to forecast the rate of losses for 21 wells. A comparison plot depicting the actual rate of lost circulation versus the predicted rate was generated as a function of depth. The results indicate that the new model is able to precisely forecast the lost circulation function of controllable drilling variables, drilling mud properties, and UCS with a correlation coefficient of 0.995.
Production logging tools (PLTs) are one type of cased hole logging, run during the production or injection stages of a well’s life, for obtaining fluid types and measuring fluid rates in the borehole for each perforation interval, and to better understand the well productivity or the well injectivity of the interest zones, also, to detect some well problems, such as cross-flow, tubing leak, casing leak. In this study, we interpreted production logging tools by Emeraude software from Kappa company to knowing which perforation interval represents the most contributing to the hydrocarbon production and to detect if there is a cross-flow problem or not, for well (X): vertical oil-producing well that belongs to (Y) oilfield, perforated with six perforation intervals, and the results were: the first two perforation intervals represent the less production interval, which accounts for 2.89 and 3.57% of the total downhole rate, and the water cut is about 27 and 32% on the surface respectively. Perforation intervals 3 and 4 do not contribute to the production. Perforation interval 5 represents the main production interval which accounts for 65.68 % of the total downhole rate, and this interval is the main water production interval with water cut about 36% on the surface, and the perforation interval 6 represents the secondary production interval which accounts for 27.86% of the total downhole rate, and the water cut is about 5% on the surface. In addition, there is no cross-flow problem, however, PLTs must be lowered in shut-in conditions to confirm this.
Drilling mud is a crucial component in the entire drilling operation. The study of the flow of matter, including gases, liquids, and solids, and how that behavior varies over time in reaction to stressors, is known as rheology in physics. In the drilling process, the rheology of the drilling fluid is crucial. This paper evaluates the rheological properties and filtration loss of calcium bentonite mud and investigates the potential for improvement to be used as drilling mud. Potential of hydrogen (pH), filtration losses, and rheological characteristics of the calcium and sodium bentonite muds were measured in the study. The calcium bentonite’s poor rheological qualities, high filtration losses, and thick mud cake were revealed by the results. Additionally, its pH was higher than that of sodium bentonite, indicating the need for improvement procedures to enhance its characteristics. Two distinct scenarios have been explored for enhancing the properties of calcium bentonite mud: the addition of NaoH and the addition of Na2CO3. Even though the results show that adding NaOH is more effective in enhancing the rheological properties of calcium bentonite than Na2CO3.The degree of improvement obtained with both NaoH and Na2CO3 is insufficient to qualify calcium bentonite for use as drilling mud.
The unconfined compressive strength (UCS) is a crucial factor of rock strength parameters for estimating the in situ stresses of the rock, designing the most effective fracture design, predicting the best mud weight, and mitigating drilling issues. UCS is commonly determined by subjecting rock samples to uniaxial or triaxial strains until they fail. Laboratory tests provide a direct and more precise estimation of UCS. However, it is unable to generate a continuous profile along the well (i.e., limited to specific depth intervals) due to the presence of specimens, expense, and time consumption. Consequently, other approaches were devised to overcome the gaps in the UCS prediction by utilizing wire-line log data. Several empirical correlations for predicting UCS are derived from well-log data, particularly the porosity, density, and sonic logs. In this paper, the previous correlations for predicting the UCS of carbonate formation have been evaluated using measured data of UCS. The results show that the compressional wave velocity (VP) is the best well log parameter for estimating carbonate formation’s unconfined compressive strength, and Yasar and Erdogan correlation best predicts the UCS that fit the measured data for carbonate formations. Thus, Yasar and Erdogan correlation has been chosen to estimate a continuous profile of UCS across the entire depth of carbonate formation in the Rumaila oil field.