Carlos Quilis Romero

Mr. Carlos Quilis Romero

orcid

Research Focus & Metrics

Academic Career Length

5Years (2022-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
8 October 2022 in Applied Catalysis B: Environment and Energy
Verified
Journal Article
Open access
CRCarlos Quilis Romero
Carlos Quilis Romero
NMNoelia Mota
Noelia Mota
BPBarbara Pawelec
Barbara Pawelec
EOElena Millan Ordoñez
Elena Millan Ordoñez
RYRufino M. Navarro Yerga
Rufino M. Navarro Yerga

24 November 2023 in Materials
Verified
Journal Article
Open access
PDF file
HLHela Lassoued
Hela Lassoued
NMNoelia Mota
Noelia Mota
EOElena Millan Ordoñez
Elena Millan Ordoñez
SRSahar Raissi
Sahar Raissi
MYMohamed Kadri Younes
Mohamed Kadri Younes
Rufino Manuel NavarroRufino Manuel Navarro
Rufino Manuel Navarro
This work is dedicated to the study of the effect of the synthesis conditions (drying and calcination) of sulfated zirconia on the final catalytic behavior of bifunctional composite catalysts prepared by the physical mixing of the sulfated zirconia (methanol dehydration catalyst) with Cu/ZnO/Al2O3 (CZA; methanol synthesis catalyst). The main objective was to optimize the CZA-ZrO2/SO42− composite catalyst for its use in the direct production of dimethyl ether (DME) from syngas. Sulfated zirconia aerogel (AZS) and xerogel (XZS) were prepared using the sol–gel method using different solvent evacuation conditions and calcination temperatures, while the Cu-ZnO(Al) catalyst was synthesized using the coprecipitation procedure. The effectivity of CZA-ZrO2/SO42− composite catalysts for the direct production of dimethyl ether (DME) from syngas was evaluated in a flow reactor at 250 °C and 30 bar total pressure. The characterization of the sulfated zirconia aerogels and xerogels using different techniques showed that the mesoporous aerogel (AZS0.5300) exhibited the best textural and acidic properties due to the gel drying under supercritical conditions and calcination at 300 °C. As a result, the composite catalyst CZA-AZS0.5300 exhibited seven times higher DME production than its xerogel-containing counterpart (364 vs. 52 μmolDME·min−1·gcat−1). This was attributed to its well-matched metal surface, mesoporous structure, optimal crystallite size and, most importantly, its higher acidity.

9 January 2025 in Catalysts
Verified
Journal Article
Open access
PDF file
CRCarlos Quilis Romero
Carlos Quilis Romero
NMNoelia Mota
Noelia Mota
BPBarbara Pawelec
Barbara Pawelec
Rufino Manuel NavarroRufino Manuel Navarro
Rufino Manuel Navarro
This study examines the factors influencing the formation and structure of ZnPd-ZnO active sites supported on TiO2 by comparing their genesis from Pd/TiO2 base catalysts prepared by impregnation using different Pd precursors (Pd(NH3)4(NO3)2 and Pd(acac)2). The experimental results demonstrated that, in contrast to the production of CO over Pd/TiO2 base catalysts, the selectivity of methanol over ZnPd-ZnO/TiO2 catalysts was significantly affected by the dispersion of ZnPd intermetallic particles and the development of ZnPd-ZnO interfaces. These are determined by the characteristics of Pd particles supported on TiO2 and their contact with the ZnO particles deposited on them. The Pd/TiO2 base catalyst prepared by impregnation with neutral Pd precursor (Pd(acac)2) produces a higher concentration and more effective dispersion of the ZnPd intermetallic phase as well as a wider ZnO-ZnPd interface region in comparison to the Pd/TiO2 counterpart synthetized using the cationic Pd precursor (Pd(NH3)4(NO3)2). These differences in the ZnPd-ZnO active sites resulted in notable variations in the methanol yield, achieving the catalysts prepared with the neutral precursor about twice higher methanol selectivity from CO2 hydrogenation at low temperatures.

5 June 2025 in ChemCatChem
Verified
Journal Article
Open access
CRCarlos Quilis Romero
Carlos Quilis Romero
NTNoelia Mota Toledo
Noelia Mota Toledo
BPBarbara Pawelec
Barbara Pawelec
Rufino Manuel NavarroRufino Manuel Navarro
Rufino Manuel Navarro
In this study, Pd/TiO2 catalysts were prepared using different methods (impregnation (IMP), chemical reduction (CR), and deposition–precipitation (DP)) to evaluate the effects of metal dispersion and metal‐support interfacial sites on the activity for the reverse water–gas shift (rWGS) reaction (CO2 + H2 ↔ CO + H2O) under low‐temperature and high‐pressure conditions. Under challenging low‐temperature reaction conditions, the highest CO yield (711.2 mmolCO·min−1·molPd−1) was achieved with the Pd/TiO2 catalyst prepared via deposition–precipitation method. Characterization results revealed that this method exhibited the best surface exposure of metallic Pd particles and altered the support morphology by decorating the TiO2 and Pd surfaces with amorphous TiO2 particles. The structure–activity correlation indicated that the key factors influencing catalyst activity and selectivity were: surface exposure and particle size of metallic Pd (from XPS, XRD, and HRTEM), the development of Pd–TiO2 interfacial region (from XPS and DRIFTS‐CO), and surface hydroxylation (from DRIFTS‐OH). The Pd‐PD catalysts with moderate SMSI seem to develop an optimal interaction that leads to better selectivity toward CO with respect to methanation.

12 September 2025 in Applied Catalysis B: Environment and Energy
Verified
Journal Article
Open access
CRCarlos Quilis Romero
Carlos Quilis Romero
NMNoelia Mota
Noelia Mota
BPBarbara Pawelec
Barbara Pawelec
PRPrabhakar Reddy
Prabhakar Reddy
JRJosé A. Rodriguez
José A. Rodriguez
Rufino Manuel NavarroRufino Manuel Navarro
Rufino Manuel Navarro