The article suggests the method for forecast of surface deformation during excavation operations in restraint urban conditions using the slurry trench technique based on FEM simulation. The results of numerical simulation of the construction of a semi-underground structure with slurry trench technique are given. The regularities of the change in the stress-strain state are determined depending on the trench parameters and the physical-mechanical properties of the soils. The work presents the troughs of surface subsidence during the construction of an excavation using the slurry trench technique. the diagrams of bending moments, transverse and longitudinal forces arising in the trench. Numerical experiments in Plaxis 2D and 3D were performed to estimate the discrepancy between modeling results in a plane and volumetric formulation of the problem.
Mine development in complex geological conditions is associated with the risk of mine stability loss. Geological features such as dykes are characterized by higher strength and a tendency to undergo brittle fracture under the influence of the tectonic component of stress. In this study, numerical simulations were conducted to analyze the zone of influence of the dyke and the extent of brittle fracture zones on the hanging and footwall sides relative to the dyke. The results indicate that the dyke’s influence zone increases when the dyke is situated in a gentle slope, and the size of the brittle fracture zone depends on the hanging and footwall sides of the rocks, as well as the dip angle of the dyke to 30%. It was observed that the rate of change in the brittle fracture zone varies non-linearly with increasing stress level and then stabilizes once the stress reaches the ultimate strength of the material. Consequently, the design of mine workings requires adjustments in support methods and stability assurance techniques within the dyke’s influence zone.
In the presented paper, an approach to assessing the size of the plastic deformation zone around a circular cavity intersecting a crushed disintegrated layer in tectonically stressed massive rock is suggested. Fractured rock zones of different quality and spatial configurations are investigated in order to predict the size of dangerous plastic deformation zones or zones of potential rock collapses. The analysis is performed by means of numerical modeling after preliminary verification of the model by in situ and monitoring data. The paper explores the impact of such parameters of the fractured rock zone as the GSI index, the true thickness of the zone, and its inclination angle relative to the plane perpendicular to the axis of the excavation. It was found that with the increase in the thickness and angle of inclination of the fractured rock zone, the size of the hazardous zone in the vicinity of the excavation increases, while with the increase in its strength characteristics, the size of the potential failure zone decreases. According to the results of the study, qualitative dependencies are established, which localize and predict the size of the danger zone, or the potential failure zone in the vicinity of an unfixed excavation.
In modern megacities, every day, people are faced with the problem of finding a place to park the cars, this problem is especially acute in the city center. The number of existing parking spaces is sorely lacking in view of the rapid growth in the number of cars. Therefore, the optimal solution for the construction and reconstruction of buildings in large metropolitan areas is the rational use of underground space, namely the construction of underground parking lots. The present work is an analysis on construction of underground and multi-story car parks in large cities through a case on the city of St. Petersburg, Russia. It considers optimal solutions for construction of underground car parks in complex geotechnical conditions using Plaxis 2D program. The purpose of the study is to develop technological solutions for the construction of underground parking lots in complex engineering and geological conditions of large megacities with the use of sheet pile fencing. Input data were collected from available engineering and geological surveys datasets obtained from construction sites. The methodology used was 2D design diagrams and a nonlinear Mohr–Coulomb model was used, which made it possible to assess as accurately as possible the geotechnical conditions in the construction area by analyzing horizontal and vertical displacements of the sheet pile wall, soil settlement at the bottom of the excavation, and the maximum settlement of a building located near the excavation. As a result, professional recommendations were developed for construction of underground and multi-storey car parks in complex geotechnical conditions: it is necessary to carry out complex geotechnical support of construction; when constructing a pit in difficult engineering and geological conditions, construct a pit with metal spacer systems (open pit); when constructing a pit near existing buildings and structures, it is very important to take into account the relative position of the base of the foundation and the pit being constructed; accurately and reliably perform calculations in the design and implementation of the construction of underground parking as part of new construction or reconstruction of previously constructed buildings in difficult engineering and geological conditions. The authors of the article have developed new technological solutions that are of great scientific and practical significance to improve the reliability and safety of preserved architectural monuments during the construction of underground parking lots, as well as the safety of neighboring buildings that may be affected by construction or reconstruction.